|
|
|
|
|
|
|
|
|
| INSTALLATION | |||
| |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| • If a remote control such as K857 is to be used with | ||||||||||||
| • Turn the Invertec® power switch "off". | the | |||||||||||
| • Connect the electrode cable to the output terminal of | to the | |||||||||||
| polarity required by electrode. (See Figures below) | Invertec® or use a K864 adapter to connect the LN- | |||||||||||
|
|
|
|
|
|
|
|
|
| 742 and the remote to the | |||
|
|
|
|
|
|
| ACROSS THE ARC MODEL | ||||||
| RANGER 9, RANGER 300 DLX |
| Output Terminals |
|
|
|
|
|
| ||||
|
| Always Hot. |
|
|
|
|
|
| |||||
| COMMANDER 300 |
|
| "ON" position or use a | wire feeder | Cobramatic Connection Instructions | |||||||
| RANGER 2V35050 |
|
| ||||||||||
|
|
| Power source contactor |
|
|
|
|
|
| ||||
| COMMANDER 500 | switch must be in the | semiautomatic | • | Turn the Invertec® power switch "off" | ||||||||
| RANGER 305G | K848 Junper Plug Kit. | |||||||||||
|
|
|
| Electrode Cable |
|
| Work | • | Connect the control cable from the Cobramatic to | ||||
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| the | |||
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| Clamp |
| ||
|
|
|
|
|
|
|
|
|
|
| • | Connect the electrode cable to the output terminal | |
|
|
|
|
|
|
|
|
|
|
|
| of the polarity required by electrode. Connect the | |
|
|
|
|
|
|
| CONTROL CABLE MODEL |
| work lead to the other terminal. | ||||
|
|
|
|
|
|
|
|
|
|
| • Set the meter polarity switch on the front of the | ||
|
|
|
|
|
|
|
|
|
|
|
| Invertec® to coincide with wire feeder polarity | |
|
|
|
|
|
|
| Electrode Cable |
|
|
|
| used. |
|
|
|
|
|
|
|
|
|
|
| • | If a remote control | such as K857 is to be used | |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| with the Cobramatic, the remote can be connected | |
|
|
|
|
|
|
|
|
|
|
|
| directly to the | |
|
|
|
|
|
|
|
|
|
|
|
| of the Invertec® or use a K864 adapter to connect | |
|
|
|
|
|
|
|
|
|
|
|
| ||
| • Set the meter polarity switch on the front of the Invertec® |
| the cobramatic and the remote to the | ||||||||||
| to coincide with wire feeder polarity used. |
| style connector. |
|
LN-25 Connection Instructions
•Turn the Invertec® power switch "off".
•Connect the electrode cable to the output terminal of polarity required by electrode. Connect the work lead to the other terminal.
•
LN-742 Connection Instructions
•Turn the Invertec® power switch "off"
•Either a K591 or a K593 Input cable assembly is required to connect the
•Connect the control cable from the
•Connect the electrode cable to the output terminal of the polarity required by electrode. Connect the work lead to the other terminal.
•Set the meter polarity switch on the front of the Invertec® to coincide with wire feeder polarity used. The wire feeder will now display the welding volt- age.
CONNECTION OF WIRE FEEDERS TO V350-PRO (CE)
Wire feeders other than these listed may be used pro- vided that the auxiliary power supply capacity of the Invertec® is not exceeded. K867 Universal Adapter Plug may be required. See connection diagram S24985 on page
REMOTE CONTROL OF INVERTEC®
Remote Control K857, Hand Amptrol K963 and Foot Amptrol K870.
UNDERCARRIAGE MOUNTINGS
MOUNTING HOLE LOCATIONS
NOTE: MOUNTING SCREWS CAN NOT PROTRUDE MORE THAN 0.5 INCHES INSIDE THE MACHINE.
3.50 |
10.00
11.84 |
| 4/01 |
|
M19527