Assistance or Service

Air conditioner power supply cord trips (Reset button pops out)

■Disturbances in your electrical current can trip (Reset button will pop out) the power supply cord. Press and release RESET (listen for click; Reset button will latch and remain in) to resume operation.

■Electrical overloading, overheating, cord pinching or aging can trip (Reset button will pop out) the power supply cord. After correcting the problem, press and release RESET (listen for click; Reset button will latch and remain in) to resume operation.

NOTE: A damaged power supply cord must be replaced with a new power supply cord obtained from the product manufacturer and must not be repaired.

Air conditioner seems to run too much

■The current air conditioner replaced an older model. The use of more efficient components may cause the air conditioner to run longer than an older model, but the total energy consumption will be less. Newer air conditioners do not emit the “blast” of cold air you may be accustomed to from older units, but this is not an indication of lesser cooling capacity or efficiency. Refer to the efficiency rating (EER) and capacity rating (in BTU/hr.) marked on the air conditioner.

■The air conditioner is in a heavily occupied room, or heat- producing appliances are in use in the room. Use exhaust vent fans while cooking or bathing and try not to use heat- producing appliances during the hottest part of the day. A higher capacity air conditioner may be required, depending on the size of the room being cooled.

Air conditioner cycles on and off too much, or does not cool/heat room in cooling/heating mode

■The Mode or Fan control is set to Power Saver (on some models). Use Power Saver only when you are asleep or away from home, since the fan does not circulate the room air continuously. Use Low Cool, Medium Cool or High Cool for your best comfort.

■The air conditioner is not properly sized for your room. Check the cooling capabilities of your room air conditioner. Room air conditioners are not designed to cool multiple rooms.

■The filter is dirty or obstructed by debris. Clean the filter.

■The inside evaporator and outside condenser coils are dirty or obstructed by debris. See “Annual Maintenance.”

■There is excessive heat or moisture (open container cooking, showers, etc.) in the room. Use a fan to exhaust heat or moisture from the room. Try not to use heat- producing appliances during the hottest part of the day.

■The louvers are blocked. Install the air conditioner in a location where the louvers are free from curtains, blinds, furniture, etc.

■The outside temperature is below 65°F (18°C). Do not try to operate your air conditioner in the cooling mode when the outside temperature is below 65°F (18°C).

■The temperature of the room you are trying to cool is extremely hot. Allow extra time for the air conditioner to cool off a very hot room.

■Windows or doors to the outside are open. Close all windows and doors.

■The Vent control is set to OPEN (on some models). Push the Vent control to CLOSED for maximum cooling and/or heating.

■The temperature set point or Thermostat control is not at a cool enough setting. Adjust the temperature set point to a cooler setting by pressing the minus button to reduce the temperature or adjust the Thermostat control to a cooler setting by turning the knob clockwise. Turn the Fan control to Turbo Cool.

■The air contitioner in the heating mode has insufficient BTU/hr for the heating requirements of the room. Do not use the air conditioner as a primary source of heat.

Temperature on display does not match room temperature

■When the compressor and fan motor turn off during Power Saver mode, or after you turn off the unit, a lower temperature reading than the actual room temperature may be displayed for a short period of time. This lower temperature reading is caused by the temperature sensor being located close to the cold evaporator coil. The actual room temperature will display within a few minutes.

Water drips from cabinet into your house

■The air conditioner is not properly leveled. The air conditioner should slope slightly downward toward the outside. Level the air conditioner to provide a downward slope toward the outside to ensure proper drainage. See the Installation Instructions.

NOTE: Do not drill a hole into the bottom of the metal base and condensate pan.

For assistance, service or replacement parts

For service assistance or to locate factory-authorized parts, call our Customer Service Center at 210-357-4400, or your nearest authorized service center. You also can visit the "Dealer Locator" at www.friedrich.com to locate your nearest authorized Friedrich Service Center.

For further assistance

If you need further assistance, you can write to ask any questions or tell us about your concerns to:

Friedrich Air Conditioning Co.

Customer Assurance

P.O. Box 1540

San Antonio, TX 78295-1540

Or email: tac@friedrich.com

Please include a daytime phone number in your

correspondence.15

CP24, CP18, CP14 specifications

Friedrich CP14, CP18, and CP24 are part of a renowned line of energy-efficient portable air conditioners designed to provide optimal cooling performance in a variety of environments. These models are especially popular for their versatility, making them ideal for residential, office, and commercial use. Each unit brings unique features and technologies that cater to different cooling requirements.

One of the standout features of the Friedrich CP series is its impressive cooling capacity. The CP14 model delivers 14,000 BTUs, the CP18 offers 18,000 BTUs, and the CP24 ramps it up to an impressive 24,000 BTUs, making them suitable for spaces ranging from small rooms to larger areas. This range allows users to select the most appropriate model based on their specific cooling needs, ensuring optimal comfort.

The CP series is equipped with an advanced air filtration system that captures dust, allergens, and other particulates from the air, resulting in cleaner and healthier indoor air quality. The reusable and washable filter not only enhances air quality but also reduces maintenance and long-term costs.

Friedrich also incorporates smart technology into the CP series, making these units easy to operate through a user-friendly control panel or remote control. The models feature comprehensive programming options, including a 24-hour timer and adjustable fan speeds, providing consumers with the flexibility to customize their cooling experience based on personal preferences.

Energy efficiency is a primary focus in the design of the CP14, CP18, and CP24 models. Each unit boasts an impressive Energy Efficiency Ratio (EER), which helps reduce electricity bills while minimizing environmental impact. The eco-friendly refrigerants used in these portable air conditioners further contribute to their environmentally conscious design.

Durability and mobility are key characteristics of the Friedrich CP series. Each unit comes equipped with casters that allow easy movement from room to room, while their compact design makes storage convenient when not in use. The robust build quality ensures that these air conditioners can withstand frequent transportation and use.

In summary, Friedrich CP14, CP18, and CP24 portable air conditioners are engineered to provide powerful cooling performance along with energy efficiency and user-friendly operation. With their advanced air filtration, customizable settings, and mobility features, these units are a perfect choice for anyone looking to enhance their indoor comfort. Whether cooling a small bedroom or a larger living space, Friedrich's CP series delivers reliable and efficient performance for all cooling needs.