Friedrich ZQ10B10 Disassembly Instructions, Mechanical Parts, Front Grille, Cabinet, Control BOX

Page 6
Figure 1
Figure 2

2.DISASSEMBLY INSTRUCTIONS

ÑBefore the following disassembly, set POWER SWITCH to OFF and disconnect the power cord.

2.1 MECHANICAL PARTS

2.1.1 FRONT GRILLE

1. Open the lnlet grille downward and remove the air filter.

2. Remove the screw which fastens the front grille.(See Figure 1)

3. Pull the front grille from the right side.

4. Remove the front grille.(There are 4 hooks.)

5. Re-install the components by referring to the removal procedure, above.

2.1.2 CABINET

1. After disassembling the FRONT GRILLE, remove the 2 screws which fasten the cabinet at both sides.

2.Remove the 2 screws which fasten the cabinet at back.

3. Pull the base pan forward. (See Figure 2)

4. Remove the cabinet.

5. Re-install the components by referring to the removal procedure, above.

2.1.3 CONTROL BOX

1. Remove the front grille. (Refer to section 2.1.1)

2. Remove the cabinet. (Refer to section 2.1.2)

3. Remove the 2 screws which fasten the power cord.

4. Disconnect the grounding screw from the evaporator channel.

5.Remove the 1 screw which fastens the control box cover.

6.Remove the housing which connects PCB(CP 08/10/12) or connector(ZQ 08/10) and motor wire in the control box.

7.Remove the nut which fastens the terminal cover.

8.Remove the terminal cover.

9. Remove all the leads from the overload protector.

10. Discharge the capacitor by placing a 20,000 ohm resistor across the capacitor terminals.

11. Raise the control box upward completely. (See Figure 3)

12. Re-install the components by referring to the removal procedure, above.

(Refer to the circuit diagram found on page 27 in this manual and on the control box.)

Figure 3

Ñ6Ñ

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Room Air Conditioner Service and Parts Manual Contents PrefaceSpecifications Or ZQ08B 10,ZQ10B 10,C P 08A10,C P 10A10,C P 12A10Features Control LocationsDIS P L AY Mote C Ontr OL Front Grille Disassembly InstructionsMechanical Parts CabinetAIR Handling Parts AIR Guide and Turbo FANElectrical Parts 2.3.1 Overload Protector CompressorPower Cord CapacitorRefrigerating Cycle Condenser CautionEvaporator Capillary Tube Pulling Vacuum Troubleshooting Guide Outside DimensionsMODELCP10A10,CP12A10 Piping System Room AIR ConitionerUnit runs but poor cooling Ineffective Cooling Fails to Start Complaint Cause Remedy Complaint Cause Remedy Schematic Diagram Model ZQ08B10,ZQ10B10Exploded View W0CZZReplacement Parts List ZQ08B10ZQ10B10 CP08A10 CP10A10 CP12A10 Memo Memo Use Factory Certified Parts

CP12A10, CP08A10, CP10A10, ZQ10B10, ZQ08B10 specifications

The Friedrich ZQ08B10, CP12A10, ZQ10B10, CP10A10, and CP08A10 represent a series of highly efficient and innovative units designed for heating and cooling applications. These systems are tailored to meet various environmental and operational demands, making them ideal for both residential and commercial sectors.

One of the main features of the Friedrich ZQ series is their energy efficiency. Equipped with advanced inverter technology, these units adjust their cooling and heating output based on the room's temperature, consuming less energy and reducing utility bills. This feature not only promotes a greener environment but also enhances users' comfort with consistent temperature control.

The ZQ08B10 and ZQ10B10 units excel in their cooling and heating capacities, making them suitable for varying room sizes. With a strong focus on versatility, these units can be installed in different configurations, including wall-mounted or ceiling-integrated systems, allowing for effective integration into existing spaces.

Another key characteristic is the quiet operation of these models. Friedrich has engineered its compressors and fans to minimize noise levels, providing a serene indoor environment. This is particularly beneficial for settings where noise can be a distraction, such as schools, offices, or residential bedrooms.

The CP series, which includes the CP08A10, CP10A10, and CP12A10, is celebrated for its smart technology features. These models come equipped with Wi-Fi connectivity, enabling users to control settings remotely via smartphone applications. This feature adds convenience and enhances energy management, allowing users to schedule operations and monitor energy consumption from anywhere at any time.

Additionally, the CP units include enhanced filtration systems designed to improve indoor air quality. Their multi-stage filters capture dust, allergens, and airborne particles, promoting a healthier living environment. This is a critical factor for households with allergy sufferers or individuals with respiratory issues.

Overall, the Friedrich ZQ08B10, CP12A10, ZQ10B10, CP10A10, and CP08A10 models stand out due to their energy efficiency, quiet operation, and smart technology features. They embody the perfect blend of performance, comfort, and advanced features, making them a valuable consideration for consumers looking for reliable heating and cooling solutions. As technology continues to evolve, these units maintain a strong position by adapting to user needs, ensuring lasting satisfaction and sustainability.
Top Page Image Contents