Makita 6019D, 6017D, 6018D instruction manual CARTRIDGEENC004-1, Functional Description

Page 4

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY

CARTRIDGEENC004-1

1.Before using battery cartridge, read all instruc- tions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.

2.Do not disassemble battery cartridge.

3.If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explo- sion.

4.If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.

5.Always cover the battery terminals with the bat- tery cover when the battery cartridge is not used.

6.Do not short the battery cartridge:

(1)Do not touch the terminals with any conduc- tive material.

(2)Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc.

(3)Do not expose battery cartridge to water or rain.

A battery short can cause a large current flow, overheating, possible burns and even a break- down.

7.Do not store the tool and battery cartridge in loca- tions where the temperature may reach or exceed 50°C (122°F).

8.Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.

9.Be careful not to drop or strike battery.

SAVE THESE INSTRUCTIONS

Tips for maintaining maximum battery life

1.Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power.

2.Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.

3.Charge the battery cartridge with room tempera- ture at 10°C - 40°C (50°F - 104°F). Let a hot battery cartridge cool down before charging it.

4.Charge the Nickel Metal Hydride battery cartridge when you do not use it for more than six months.

FUNCTIONAL DESCRIPTION

CAUTION:

•Always be sure that the tool is switched off and the bat- tery cartridge is removed before adjusting or checking function on the tool.

Installing or removing battery cartridge (Fig. 1)

•Always switch off the tool before insertion or removal of the battery cartridge.

•To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool.

•To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Be sure to close the set plate fully before using the tool to pre- vent the battery cartridge from accidentally falling out of the tool.

•Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly.

Switch action (Fig. 2)

CAUTION:

•Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released.

To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop.

Reversing switch action (Fig. 3)

This tool has a reversing switch to change the direction of rotation. Move the reversing switch lever to the A side for clockwise rotation or the B side for counterclockwise rota- tion.

When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled.

CAUTION:

•Always check the direction of rotation before operation.

•Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool.

•When not operating the tool, always set the reversing switch lever to the neutral position.

Speed change (Fig. 4)

To change the speed, first switch off the tool and then slide the speed change lever to the “II” side for high speed or “I” side for low speed. Be sure that the speed change lever is set to the correct position before operation. Use the right speed for your job.

CAUTION:

•Always set the speed change lever fully to the correct position. If you operate the tool with the speed change lever positioned halfway between the “I” side and “II” side, the tool may be damaged.

•Always make sure that the gear is engaged properly by running the tool under no load after sliding the speed change lever to the desired speed position. If you oper- ate the tool with the gear engaged improperly, the tool may be damaged.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents 6017D 6018D 6019D Page Specific Safety Rules GEB002-2 SpecificationsIntended use CARTRIDGEENC004-1 Functional DescriptionMaintenance AssemblyOperation Accessories Technische Gegevens GebruiksdoeleindenBelangrijke Veiligheidsinstructies Voor ACCU’S Bewaar Deze VoorschriftenBeschrijving VAN DE Functies Onderdelen AANBRENGEN/ Verwijderen BedieningAccessoires OnderhoudGebruik als boor zie afb Boren in houtEC-DECLARATION of Conformity Déclaration DE Conformité CELE Norme Della Comunità Europea EG-VERKLARING VAN ConformiteitDeclaração DE Conformidade DA CE EU-DEKLARATION OM KonformitetEG-DEKLARATION OM Överensstämmelse Vakuutus EC-VASTAAVUUDESTAFor European countries only Noise and Vibration Pour les pays d’Europe uniquement Bruit et vibrationsModello per l’Europa soltanto Rumore e vibrazione Alleen voor Europese landen Geluidsniveau en trillingSó para países Europeus Ruído e vibração Kun for lande i Europa Lyd og vibrationEndast för Europa Buller och vibration Gjelder bare land i Europa Støy og vibrasjonPage Page Makita Corporation Anjo, Aichi, Japan

6018D, 6017D, 6019D specifications

The Makita 6019D, 6017D, and 6018D are robust cordless impact drivers renowned for their reliability and performance in various applications. Each model is designed to cater to different user needs while maintaining Makita's high standards for quality and durability.

The Makita 6019D stands out with its powerful motor and an impressive torque rating, making it ideal for heavy-duty tasks. This model features a compact design that enables users to work in tight spaces without compromising on performance. Moreover, its lightweight structure reduces user fatigue, allowing for extended use during prolonged projects. The 6019D is equipped with a variable speed control, enabling users to adjust the speed based on the specific requirements of the task, promoting precision and efficiency.

The Makita 6017D is recognized for its exceptional versatility and ergonomic design. It incorporates advanced technology such as an electronic brake for increased control and safety while working. The 6017D's lightweight design, combined with its thoughtful grip design, ensures comfort during extended use. This model also includes an integrated LED job light, illuminating the work area for improved visibility in low-light conditions. With a high-capacity battery, the 6017D offers excellent runtime, making it suitable for professionals and DIY enthusiasts alike.

On the other hand, the Makita 6018D boasts cutting-edge technology that enhances user convenience and performance. Featuring an efficient brushless motor, this model ensures longer runtime and increased productivity. The brushless technology also translates to less maintenance and a longer lifespan for the tool. The compact and lightweight design of the 6018D makes it a favorite for users who require a tool that is easy to handle without sacrificing power. Additionally, it offers multiple speed settings and a reverse function, adding versatility to different applications.

In summary, the Makita 6019D, 6017D, and 6018D are each distinguished by their unique features and advanced technologies. These impact drivers are engineered to meet the demands of various users, from professionals seeking high-performance tools to hobbyists looking for reliable equipment. With their user-friendly designs, powerful motors, and thoughtful features, these models underline Makita's commitment to excellence in the power tool industry. Whether it's construction, woodworking, or maintenance work, these impact drivers deliver exceptional performance and reliability.
Top Page Image Contents