Cabela's 18868 manual General Operation, LED Status Center- Operation & Display

P r o S p o r t O v e r v i e w

5

General Operation

Install your ProSport On-Board Marine Battery Charger to the guidelines in this manual.

Make sure your charger and batteries are properly vented. Connect your extension cord with no AC Power present to the ProSport and proceed to plug your extension cord in at a nearby 120 VAC GFCI protected (Ground Fault Circuit Interrupt) outlet.

I n s t a l l a t i o n G u i d e l i n e s

10

ProSport Series Wiring Diagrams

ProSport Wiring Diagrams for Typical Installations of 12 Volt DC and 24 Volt DC Trolling Motor Battery Configurations with a Dedicated Engine Start Battery. (ProMariner recommended configuration. )

With your ProSport plugged in properly, it will automatically / fully charge your batteries while it conditions and extends the life of your batteries. When you’re not at home, always leave your charger plugged in to reduce sulfate build-up allowing your batteries to be fully charged and maintained for your next fishing trip.

For long term or winter storage/ maintenance of batteries, ProMariner recommends that every 30 days: AC Power is removed by unplugging your extension cord at the GFCI outlet first, check battery electrolyte levels. Re-apply AC power to your ProSport Charger. This practice will properly maintain your batteries resulting in extended Battery Life and Use.

Fig. 1 ProSport 8, 12,& 20 Dual Output Charger

for 2 Batteries Maximum Typical

12 VDC Trolling Motor Battery Configuration Plus Dedicated 12 VDC Engine Start Battery

AC power

output no.1

output no.2

Fig. 2 ProSport 20 Plus Triple Output Charger

for 3 Batteries Maximum Typical

24 VDC Trolling Motor Battery Configuration

with (2) 12 VDC Batteries Connected with a Series Jumper

Plus Dedicated 12 VDC Engine Start Battery

AC power output no.1

output no.2

output no.3

LED Status Center- Operation & Display

The ProSport Series includes four (4) LEDs as shown:

1.Top LED is Battery Type: Red for Flooded (Lead-acid)/AGM & Amber for GEL

2.Ready LED: Illuminates Green

3.Charging LED: Illuminates Red

4.Bottom Power LED: Illuminates Blue

LED Status Center Operation after Applying AC Power to Discharged Batteries (Example below is for the factory setting of Flooded (Lead-acid) batteries)

red yellow red yellow

	+	_		+	_
12 VDC Trolling			12 VDC Engine
Motor Battery			Crank Battery

Note:

Indicates Jumper Series

Indicates Fuse

red yellow red yellow red yellow

+	_	+	_	+	_
				12 VDC Engine
Two 12 VDC Batteries connected with a
series jumper for a 24 VDC Trolling Motor				Crank Battery

The Blue AC Power LED will illuminate followed by the Red Charging LED and Red Battery Type LED (Factory Setting for Flooded (Lead-acid)/AGM Batteries). The combination of these three LEDs turning on indicates ProSport has started

ProSport Wiring Diagrams for Typical Installations of 12 Volt DC, 24 Volt DC and 36 Volt DC Dedicated Trolling Motor Battery Configurations. No Engine Start Battery.

its Sequential Multi-Stage Charging process.

When the Sequential Multi-Stage Charge Process is completed you will observe the following:

Battery Type Red LED goes OFF

Charging Red LED goes OFF Ready Green LED turns ON

The only LEDs on after the Sequential Multi-Stage Charge process is completed are the Blue AC Power LED and the Green Ready LED

Fig. 3 ProSport 6 Single Output Charger

for 1 Battery Maximum Typical

Dedicated 12 VDC Trolling Motor Battery Configuration

AC power

output no.1

Fig. 4 ProSport 8, 12, & 20 Dual Output Charger

for 2 Batteries Maximum Typical

Dedicated 24 VDC Trolling Motor Battery Configuration with (2) 12 VDC Batteries Connected with a Series Jumper

AC power

output no.1

output no.2

LED Status Center Operation after Applying AC Power to Fully Charged Batteries

The Blue AC Power LED will illuminate followed by the Green Ready Indicator turning ON

For this application, the following LEDs are in the OFF state.

Battery Type (factory set) Red LED Turns OFF

Charging Red LED Turns OFF.

The only LEDs on, if the charger is maintaining fully charged batteries, are the Blue AC power LED and the Green Ready LED.

red	yellow	Note:
+	_	Indicates Jumper Series
		Indicates Fuse

12 VDC Trolling Motor Battery

red	yellow	red	yellow
+	_	+	_

Two 12 VDC Batteries connected with a series jumper for a 24 VDC Trolling Motor