Start UP

IMPORTANT INSTALLER NOTE

For improved start-up performance, wash the indoor coil with a dishwasher detergent.

CRANKCASE HEATERS

All units are provided with some form of compressor crankcase heat.

All single and three phase models have an insertion well-type heater located in the lower section of the compressor housing. This is a self-regulating type heater that draws only enough power to maintain the compressor at a safe temperature.

Some form of crankcase heat is essential to prevent liquid refrigerant from migrating to the compressor, causing oil pump out on compressor start up and possible valve failure due to compressing a liquid.

The decal in Figure 9 is affixed to all outdoor units detailing start up procedure. This is very important. Please read carefully.

SERVICE HINTS

1.Caution homeowner to maintain clean air filters at all times. Also, not to needlessly close off supply and return air registers. This reduces air flow through the system, which shortens equipment service life as well as increasing operating costs.

2.Check all power fuses or circuit breakers to be sure they are the correct rating.

3.Periodic cleaning of the outdoor coil to permit full and unrestricted airflow circulation is essential.

SEQUENCE OF OPERATION

Cooling—Circuit R-Y makes at thermostat pulling in compressor contactor, starting the compressor and outdoor motor. The G (indoor motor) circuit is automatically completed on any call for cooling operation or can be energized by manual fan switch on subbase for constant air circulation. On all 230 volt units there is a one minute off delay on the blower motor. 460 volt models do not have an off delay. On a call for heating, circuit R-W1 make at the thermostat pulling in heat contact for the strip heat and blower operation. On a call for second stage heat, R-W2 makes bringing on second heat contactor, if so equipped.

COMPRESSOR CONTROL MODULE

The compressor control module is optional on the models covered by this manual. The compressor control is an anti-short cycle/lockout timer with high and low pressure switch monitoring and alarm relay output.

Adjustable Delay On Make And Break Timer

On initial power up or any time power is interrupted to the unit the delay on make period begins which will be

2 minutes plus 10% of the delay on break setting. When the delay on make is complete and the high pressure switch (and low pressure switch if employed) is closed, the compressor contactor is energized. Upon shutdown the delay or break timer starts and prevents restart until the delay on break and delay on make periods have expired.

During routine operation of the unit with no power interruptions the compressor will operate on demand with no delay.

FIGURE 9

START UP LABEL

IMPORTANT

These procedures must be followed at initial start up and at any time power has been removed for 12 hours or longer.

To prevent compressor damage which may result from the presence of liquid refrigerant in the compressor crankcase:

1.Make certain the room thermostat is in the "off" position (the compressor is not to operate).

2.Apply power by closing the system disconnect switch. This energizes the compressor heater which evaporates the liquid refrigerant in the crankcase.

3.Allow 4 hours or 60 minutes per poind of refrigerant in the system as noted on the unit rating plate, whichever is greater.

4.After properly elapsed time, the thermostat may be set to operate the compressor.

5.Except as required for safety while servicing, do not open system disconnect switch.

7961-061

Manual 2100-192 Page 13

WA301, WA361 specifications

The Bard WA361 and WA301 are two advanced wall-mounted air conditioning systems designed for commercial and residential use. These units are engineered to provide efficient cooling and heating while optimizing energy consumption.

One of the standout features of the Bard WA361 and WA301 models is their compact design. This allows for easy installation in various spaces where traditional floor-mounted units may not fit. Ideal for areas such as classrooms, offices, or small retail locations, these units can be mounted high on the wall, freeing up valuable floor space.

Both models leverage Bard’s advanced heat pump technology. This technology allows for reverse-cycle functionality, meaning they can provide both cooling in summer and heating in winter. The WA361 model offers a heating capacity of up to 36,000 BTUs while the WA301 provides a slightly lower capacity of 30,000 BTUs, making them suitable for different size requirements.

Energy efficiency is prioritized in these models. They come equipped with high Seasonal Energy Efficiency Ratings (SEER), which ensures lower electric bills and reduced environmental impact. Additionally, the units have been designed to operate quietly, maximizing comfort without the disruptive noise often associated with HVAC systems.

Another notable characteristic is the advanced control system. The Bard WA361 and WA301 feature programmable thermostats that allow users to set specific comfort levels according to their schedules. This not only enhances user control but also boosts energy-saving potential.

Moreover, both models are built with durable materials to ensure longevity and reliability. Their internal components are engineered to withstand harsh conditions, making them a preferred choice for various settings, including industrial environments.

Bard emphasizes ease of maintenance in the design of these units. The filters are easily accessible and can be replaced or cleaned with minimal effort. This feature significantly extends the lifespan of the unit and ensures that it operates at peak performance.

In summary, the Bard WA361 and WA301 air conditioning units represent a blend of innovative technology and practical design. Their energy-efficient operation, compact installation capability, and advanced heating and cooling functions make them exemplary solutions for those seeking reliable comfort control in diverse applications. Whether for small businesses or residential spaces, these units aim to deliver exceptional performance with a focus on sustainability and efficiency.