Associated Equipment BC-91305 Charge Period, Operating Instructions, Possible Charging Problems

Page 3

DANGER. Before using an adapter as illustrated, be certain that the center screw of the outlet plate is grounded. The green-colored rigid ear or lug extending from the adapter must be connected to a properly grounded outlet - make certain it is grounded. If necessary, replace the original outlet cover plate screw with a longer screw that will secure the adapter ear or lug to the outlet cover plate and make ground connection to grounded outlet.

NOTE: USE OF AN ADAPTER IS NOT ALLOWED IN CANADA. IF A GROUNDING TYPE RECEPTACLE IS NOT AVAILABLE, DO NOT USE THIS APPLIANCE UNTIL THE PROPER OUTLET IS INSTALLED BY A QUALIFIED ELECTRICIAN.

21.CHARGE PERIOD

The approximate required time to bring a battery to full charge state depends upon the number of ampere-hours (AH) depleted from the battery. AH's are determined by multiplying the number of hours times the number of amps supplied by a battery to a load and normally indicated on the battery. For example, if a load was connected to a battery, which drew 7 amps for a period of 5 hours, the battery will have supplied 35 AH. The approximate recharge time would then be calculated by dividing the 35 AH depleted from the battery, by the charge rate of the charger. To allow for tapering of the charge rate add 25 percent to the charge time.

OPERATING INSTRUCTIONS

This battery charger is designed to charge 12 volt batteries of either conventional or maintenance-free construction. Rated output current is 1.5 DC amps. When operating this charger, carefully follow the instructions in sections 17 and 18.

POSSIBLE CHARGING PROBLEMS

This battery charger has been equipped with an automatic reset circuit breaker. This protects the charger from temporary overload conditions. A severely discharged battery, a battery with shorted cells, or reversed charger connections at the battery will cause this protective device to operate. Under these overload conditions, the circuit breaker will open, and when cooled down will reset automatically. This cycling process can be identified by a clicking sound made during the opening and closing of the circuit breaker.

a.Check for reverse polarity connections.

b.The battery may have one or more shorted cells. Cycling will start immediately and continue indefinitely. If cycling has not stopped, disconnect the charger (AC power cord first) and have the battery tested.

MAINTENANCE INSTRUCTIONS

This charger requires minimal maintenance. As with any appliance or tool, a few common sense rules will prolong the life of the battery charger. ALWAYS BE SURE THE CHARGER IS UNPLUGGED BEFORE PERFORMING ANY MAINTENANCE OR CLEANING.

1.Store in a clean, dry place

2.Coil up the cords when not in use.

3.Clean the case and cords with a slightly damp cloth.

4.Clean any corrosion from the clamps with a solution of water and baking soda.

5.Examine the cords periodically for cracking or other damage and have them replaced if necessary.

6.WARNING: All other service should be done by qualified personnel only.

3

Image 3
Contents Preparing to Charge Important Safety InstructionsPersonal Precautions Operators ManualVehicles with TWO Batteries DC Connection PrecautionsGrounding and AC Power Cord Connection Instructions Charger LocationOperating Instructions Possible Charging ProblemsMaintenance Instructions Charge PeriodPage Instructions DE Sécurité Importantes Manuel DutilisationVehicules Avec Deux Batteries 16. Précautions Relatives AUX Connexions c.cInstructions Pour Lentretien Problemes Possible Lors DE LA Charge21. Période DE Charge Instructions DutilisationsPage Preparando Para Cargar Manual DE InstruccionesAtención Riesgo DE Gases Explosivos Precauciones PersonalesPeríodo DE Carga Precauciones Para LA Conexión DCVehículos CON DOS Baterías Instrucciones DE Conexión a Tierra Y Conexión ACPosibles Problemas DE Carga Instrucciones DE Operación DE LOS Modelos 9305 Y BC-91305Instrucciones DE Mantenimiento Associated Equipment Corporation Limited Warranty