Kawasaki 840138-1HR instruction manual Removing / Attaching Battery Pack

Page 17

BATTERY

Before using battery pack, please read carefully all instructions and cautionary markings on battery pack, battery charger and product using battery.

®

Do not incinerate the battery pack even if it is severely dam- aged or is completely worn out. The battery pack can explode.

Do not carry battery packs in aprons, pockets, or tool boxes, product kit boxes, drawers, etc. with loose metal objects. Battery pack terminals could be short circuited causing damage to the battery pack, severe burns or fire.

The battery pack is Nickel-Cadmium (Ni-Cad) and is considered to be a toxic material by the Environmental Protection Agency. Before disposing of dam- aged or worn out Ni-Cad battery packs, check with your State Environmental Protection Agency to find out about special restrictions on the disposal of these battery packs, take them to your local recycling center for proper disposal, or call 1-800-822-8837.

The battery is not fully charged. Before first use, the battery pack requires 3-5 hours charge time to be fully charged. Subsequent recharging needs 1 hour for the battery to be fully charged.

Always switch to a fresh battery when tool performance begins to diminish. Severe heat is most destructive to a battery; the more heat generated, the faster the battery loses power. A battery that gets too hot can have a shortened life.

Never over-discharge a battery by using the tool even after tool performance has decreased. Do not attempt to discharge a tool’s battery by continuing to pull on the tool trigger. When tool performance begins to diminish, stop the tool and recharge the battery for optimal performance.

Charge battery pack at ambient temperatures between 50° F – 104° F.

Store tool and battery pack in locations where temperatures will not exceed 120°F. This is important to prevent serious damage to the battery cells.

The battery pack should always be recharged when the Cordless Worklight begins to dim.

When battery pack is not in use, keep it away from other metal objects such as paper clips, coins, keys, nails, screws or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns, or fire.

REMOVING / ATTACHING BATTERY PACK

REMOVE BATTERY PACK:

1. Press both release buttons on either side of

the Cordless Worklight to release the battery pack.

2. Pull battery pack free of Cordless Worklight.

ATTACH BATTERY PACK:

1. Align the raised portion of the battery pack with the groove in the battery compart- ment

of the Cordless Worklight.

2. Press the battery pack into place. Make

 

sure the latches are securely fastened.

 

Do not use the Cordless Worklight if the

RELEASE

battery pack is not seated properly.

BUTTON

CHARGER

Before using battery charger, please read carefully all instructions and cautionary markings on battery charger, battery pack and product using battery.

Use only the charger which accompanied your product or direct replacement as listed in this manual. Do not substitute any other charger. Use only Alltrade approved chargers with your product.

Do not disassemble charger.

Do not use charger if it has been damaged, left outdoors in the rain, snow, wet or damp environments, or immersed in liquid.

The battery pack and charger heat during charging. Place the charger on a flat, non-flammable surface away from flammable materials with at least four inches of clearance to allow proper air circulation around the charger and battery pack.

When the battery pack requires recharging, a 1 hour charge allows the tool to operate at full power. A charging indicator light on the charger will illuminate to show that charging is taking place.

7

8

Image 17
Contents 19.2V 2-SPEED BATTERY-OPERATED Drill General Safety Rules for ALL Battery Operated Tools Table of ContentsRecognize Safety SYMBOLS, Words and Labels CongratulationsElectrical Safety Important SafeguardsPersonal Safety Save These Instructions for Future ReferenceSpecific Safety Rules AND/OR Symbols ServiceSafety Rules for Cordless Drill / Drivers Tool USE and CareSymbol Name Explanation SymbolsAccessories Functional DescriptionREMOVING/ATTACHING Battery Pack BatteryRemove Battery Pack Attach Battery PackAssembly Charging Battery PackInstalling Drill BIT Into Keyless Chuck Important Information for Recharging HOT BatteriesTorque Settings Variable Speed Trigger SwitchForward / Reverse and Trigger Lock Lever HIGH/LOW Speed Gear ShiftingDrilling Metal Maintenance and CleaningDrilling Masonry Drilling WoodSpecifications AccessoriesConductor Size in A.W.G Protecting the EnvironmentCommercial or Rental Purpose Year Limited WarrantyWarranty Disclaimers 19.2V BATTERY-OPERATED Worklight Safety Rules for Worklight Symbols Safety Rules for Worklight Battery Tool USE and CareComponent Model Number Controls and ComponentsRemoving / Attaching Battery Pack Operating the on / OFF Switch Charge Battery PackAdjusting the Worklight Beam Operating the WorklightTool Current Rating Recommended Sizes of Extension Cords 120 Volt AC 60 HZ ToolsCorded and Cordless Multi-Purpose Tools Exclusions 19.2V Battery Pack Congratulations Symbols Which Extend Beyond the Description on the Face Hereof Year Limited Home USE WarrantyWarranty Disclaimers