Kawasaki 840055 Operating the Circular SAW, Operating the Trigger Switch, General Cutting

Page 42

OPERATING THE CIRCULAR SAW

Never tape the trigger switch down to provide continuous high speed. The tool may fail under such conditions causing fire or personal injury.

The lock-off button helps prevent accidental starting. This button can be pressed from either side.

OPERATING THE TRIGGER SWITCH

THIS TOOL IS CONTROLLED BY A

LOCK-OFF BUTTON

TRIGGER SWITCH

 

 

TRIGGER SWITCH:

 

 

• Press the lock-off button, then pull

 

 

the “ON/OFF” trigger to turn the

 

 

Circular Saw “ON”. To turn the

 

 

Circular Saw “OFF”, release the

 

 

trigger switch. The lock-off button

 

 

will automatically reset.

 

 

GENERAL CUTTING

Always hold the saw in front of you and away from your body. Keep your hands and feet well away from the work piece.

Never feed the blade into the work piece until the blade is at full speed. If the blade is not at full speed, the saw may kick back causing serious personal injury.

Do not force the saw. Excessive force may result in a broken blade. Use only enough pressure to keep the saw moving through the work piece.

•Put on eye protection.

•Clear the saw of any foreign material.

•Make sure the work piece is held securely in place. Hold smaller pieces in a vise or attach to the workbench with clamps.

•Mark out the line to be cut so it is easily visible.

•Check the lower guard for damage. If damaged, do not use tool.

•Always use the right blade for the material.

•Make sure all bolts, screws and locking levers are secure before starting tool.

•Pull the trigger to start the saw.

•Set the shoe against the work piece.

•When the blade reaches full speed, slowly feed the blade into the work piece. When the blade starts cutting, release the blade guard.

POCKET CUTTING

If the blade binds, release the trigger immediately. Do not move the saw until the blade comes to a complete stop. Find the cause of the binding before starting the saw again.

If the blade becomes pinched, twisted, misaligned or bound, it will stall and lift up out of the work piece, suddenly jerking back toward the operator. This reaction is referred to as KICKBACK.

• Mark out the line to be cut so it is easily visible.

• Start inside the area to be cut out.

• Set the shoe against the work piece at an angle.

• Lift the blade guard.

• Pull the trigger to start the saw.

• When the blade reaches full speed, slowly feed the blade into the work piece. When the blade starts cutting, release the blade guard.

17

18

Page 41 Page 43
Image 42
Page 41 Page 43
Contents 19.2V 2-SPEED BATTERY-OPERATED Drill Recognize Safety SYMBOLS, Words and Labels Table of ContentsGeneral Safety Rules for ALL Battery Operated Tools CongratulationsElectrical Safety Work AreaPersonal Safety ServiceTool USE and Care Symbols Specific Safety Rules AND/OR SymbolsSafety Rules for Cordless Drill / Drivers Symbol Name ExplanationFunctional Description Battery AccessoriesComponent Model Number REMOVING/ATTACHING Battery Pack Charger Charging Battery PackAssembly Forward / Reverse and Trigger Lock Lever This Tool is Controlled By a Trigger SwitchBuilt in LED Lamp Operating the DrillDrilling Metal Torque SettingsScrewdriving Drilling Masonry High / LOW Speed Gear ShiftingScrewdriving Maintenance and CleaningAccessories Conductor Size in A.W.GProtecting the Environment SpecificationsYear Limited Home USE Warranty Other Consumer DO-IT-YOURSELF DIY ToolsExclusions 19.2V BATTERY-OPERATED Jigsaw Recognize Safety SYMBOLS, Words and Labels Table of ContentsGeneral Safety Rules for ALL Battery Operated Tools CongratulationsImportant Safeguards Electrical SafetyWork Area Specific Safety Rules AND/OR Symbols Personal SafetyService Safety Rules for Cordless JigsawsRing Selector Settings SymbolsSymbol Name Explanation Could become entangled with clothing and injury may resultFunctional Description Battery Component Model NumberAssembly Removing / Attaching Battery PackCharging Battery Pack ChargerOperating the on / OFF Switch General Cutting Operating the JigsawPlunge Cutting Specifications Maintenance and CleaningAccessories Metal CuttingYear Limited Home USE Warranty Other Consumer DO-IT-YOURSELF DIY ToolsWarranty Disclaimers 87-1904-60957 Congratulations Table of ContentsRecognize Safety SYMBOLS, Words and Labels Intended USEBattery Tool USE and Care ServiceSafety Rules for Worklight Functional Description SymbolsSymbol Name Explanation Component Model NumberRemove Battery Pack BatteryRemoving / Attaching Battery Pack Attach Battery PackOperating the on / OFF Switch Charging Battery Pack Adjusting the Worklight BeamCharge Battery Pack Operating the WorklightSpecifications AccessoriesMaintenance and Cleaning Tool Current RatingYear Limited Home USE Warranty Warranty PerformanceOther Consumer DO-IT-YOURSELF DIY Tools Limitation Of Liability Component #840055 General Safety Rules for ALL Battery Operated Tools Electrical Safety Work AreaPersonal Safety Specific Safety Rules AND/OR SymbolsTool USE and Care Safety Rules for Circular SAW Causes and Prevention of KickbackComponent SAW BladesRIP Fence Control FeaturesDepth RIP Fence Lock KnobRed LED indicator light will remain on Removing / Attaching Battery Pack Charging Battery PackPull battery pack free Cordless Circular Saw AssemblyAdjusting Depth and Angle Attaching / Removing BladeGeneral Cutting Operating the Trigger SwitchOperating the Circular SAW Pocket CuttingAmpere VoltageYear Limited Home USE Warranty Warranty Disclaimers
Top Page Image Contents