Hitachi NR-7000 Preparation before use, How to put in a battery, Before use, Ion cleansing mode

Preparation before use

How to put in a battery

Precautions on using a battery

1.Do not use a leaky battery.

2.Use only an alkaline battery (size AA).

●With other batteries (rechargeable batteries, etc.), full performance will not be delivered as the power is low or the battery life is short.

3.Correctly put in an alkaline battery according to the (＋) and (－) indications on the main body.

4.Use a battery that is within the recommended period of use.

5.Immediately take out the battery when used up.

6.Dispose of used batteries according to your local laws and regulations, etc.

●The battery life will differ depending on the ambient temperature.

[When this product is used for about 4 minutes

(2 minutes in each mode) once a day with a Hitachi alkaline battery LR6 (EX-S)]

●About 3 weeks at an ambient temperature of 25°C

●About 2 weeks at an ambient temperature of 15°C The battery life has run down if the indication lamp does not flash/light even when the switch is turned ON. Replace the alkaline battery with a new one.

1.Pull and remove the main body case in the direction of the arrow. (Fig.2)

CAUTION

●Do not remove the upper cap.

●Remove the main body case holding the main body.

2.Correctly put in a size AA alkaline battery according to the indications on the main body. (Fig.3)

Size AA alkaline battery

CAUTION

●If the battery is put in incorrectly, the indication lamp will not light/flash.

3.Install the main body case.

Align the depressions in the main body case with the projections on the main body, and securely install the

main body case as far as it will go. (Fig.4)

Projections	Depressions
Before use
1. Modes
Mode	Item(s) used together
I. Ion cleansing	- Cotton swab
	- Your regular toner
II. Heating care	- Your regular lip balm
	-5-

2. Mode switching

(Double press)

			(Switch press
Switch	(Single press)	Ion cleansing	in mid-process)	Heating care
(OFF)

(Lapse of 2 minutes)

(Switch press in mid-process or a lapse of 2 minutes)

In ion cleansing mode

Persons who use embedded or wearable medical electronic devices should never use this product. (This product may cause medical electronic devices to malfunction.)

Remove jewelry and contact lenses. (Cause of skin trouble or poor physical condition)

●Use the ion cleansing mode within 2 minutes once a day.

●Do not use this product more than 2 minutes

continuously; otherwise it may cause lip trouble.

1.Wash away dirt from lips cleanly.

●Remove lipstick, etc., with a cleansing agent.

2.Cut a commercially available cotton swab and set it to the main body.

(1) Remove the lower cap. (Fig.5)

(2) Cut a commercially available cotton swab so that its

stem portion becomes 5 to 10mm. (Fig.6)

Stem portion 5 to 10mm

How to determine the cutting size

The locating hole is intended to determine the cotton swab length.

※A paper-made stem can be cut by the locating hole. If the stem portion of the cotton swab is plastic, crease it with the locating hole, and then cut it with scissors.

If you do not use the locating hole, cut the cotton swab so that its stem portion becomes 5 to 10mm.

(1) Insert the cotton swab in the locating hole in the lower cap, and push the stem portion into the narrowed part of the hole. (Fig.7)

(2) Draw out the stem portion frontward, and it stops at a position of about 7mm. Incise and cut the stem

within 3mm from the surface of the lower cap. (Fig.8)

About 7mm Within 3mm Maximum cutting position

(3)If the stem portion of the cotton swab is made of paper, it can be cut off by folding it from side to side as it is. (Fig.9)

-6-