Hitachi C10FL Crosscutting Fig. Y To prevent serious injury, Bevel Crosscutting Fig. AA

Page 21

CROSSCUTTING (Fig. Y) To prevent serious injury:

Do not allow familiarity or frequent use of your table saw to cause careless mistakes. Remember that even a careless fraction of a second is enough to cause a severe injury.

Keep both hands away from the blade and the path of the blade.

1.Remove the rip fence and place it in the "storage" compartment of the table saw base.

2.Place the miter gauge either groove in the table top.

3.Adjust the blade height so it is 1/8" higher than the top of the workpiece.

4.Hold the workpiece firmly against the miter gauge with the blade path in line with the desired cut location.

5.Start the saw and wait for the blade (1) to come up to full speed.

6.Keep the workpiece (2) against the face of the miter gauge (3) and flat against the table. Then slowly push the workpiece through the blade. (Fig. Y)

7.Do not try to pull the workpiece back with the blade turning. Turn the switch OFF, wait for the blade to come to a complete stop, then carefully slide the workpiece.

Fig. Y

3

 

 

2

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

USING WOOD FACING ON THE MITER GAUGE (Fig. Z) Slots are provided in the miter gauge for attaching an auxiliary facing (1) to make it easier to cut very long or short pieces. Select a suitable piece of smooth wood, drill two holes through it and attach it to the miter gauge with screws. Make sure the facing does not interfere with the proper operation of the sawblade guard. When cutting long workpieces, you can make a simple outfeed support by clamping a piece of plywood to a sawhorse.

Fig. Z

1

BEVEL CROSSCUTTING (Fig. AA)

This cutting operation is the same as crosscutting except the blade is at bevel angle other than 0 .

1.Adjust the blade (1) to the desired angle, and tighten the blade bevel lock knob.

2.Always work to the left side of the blade. The miter gauge (3) must be in the left side groove (2).

Fig. AA

31

2

COMPOUND MITER CROSSCUTTING (Fig. BB)

This sawing operation is combining a miter angle with a bevel angle.

1.Set the miter gauge (3) to the desired angle. Use only the left side groove (2) for this specific operation.

2.Set the blade (1) bevel to the desired angle.

3.Carefully push the miter gauge to begin the cutting operation.

Fig. BB

3 2 1

MITERING (Fig. CC)

This sawing operation is the same as crosscutting except the miter gauge is locked at an angle other than 90

1.Hold the workpiece (2) firmly against the miter gauge (3).

2.Feed the workpiece slowly into the blade (1) to prevent the workpiece from moving.

Fig. CC

3 2 1

— 21 —

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 10FL Hitachi Authorized Service Centers Product Specifications Motor SAWYES Check for Damaged or Loose Parts Power Tool SafetyTable SAW Safety Power Supply Requirements Electrical Requirements and SafetyExtension Cord Requirements Guidelines for Extension CordsTools Needed for Assembly Accessories and AttachmentsRecommended Accessories Tools NeededCarton Contents Unpacking Your Stationary Table SAW Know Your Stationary Table SAW Hitachi Professional Table SAW Terms Glossary of TermsWoodworking Terms Workpiece workpiece are edgesAssemble Table SAW to Stand Fig. A, B Assembly and AdjustmentsAssembly the rear table rail Fig. E Assembly the Table Extension Fig. CBlade Raising Handwheel Fig. F Blade Tilting Handwheel Fig. FFrom the power source outlet Switch is in the OFF position and the plug is disconnectedRemoving the blade guard assembly Fig. H To avoid injury from an accidental start, make sureStop Fig. JFig. K Blade Tilting Indicator Fig. LPower Cord Fig. P Installing the Table Insert Fig. NMitre Gauge Adjustment Fig. Q Storage Fig. O, P Rip fence and miter gauge Fig. ORIP Fence Adjustment Fig. R RIP Fence Indicator Fig. TRIP Fence Operation Basic SAW Operations OperationTilting the Blade Overload ProtectionRipping Fig. W Bevel RippingRipping Small Pieces Bevel Crosscutting Fig. AA Crosscutting Fig. Y To prevent serious injuryCompound Miter Crosscutting Fig. BB Mitering Fig. CCMaking the side Auxiliary Fence Fig. EE Making the basePutting it together Dado Cuts Fig. GGMaintenance Maintaining Your Table SAWLubrication Terminal Block Symptom Possible Causes Corrective Action Troubleshooting GuidePush Stick Page Parts List Parts List for Schematic aStationary Table SAW Statonary Table SAW Model NO. C10FL Schematic a Statonary Table SAW Model NO. C10FL Parts List for Schematic BStatonary Table SAW Model NO. C10FL Schematic B Hitachi Koki Canada Co
Top Page Image Contents