Hitachi C10FL instruction manual Product Specifications, Motor SAW, Yes

Page 3

WARNING

Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•Lead from lead-based paints

•Crystalline silica from bricks, cement and other masonry products

•Arsenic and chromium from chemically treated lumber

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment such as dust masks that are specially designed to filter out microscopic particles.

PRODUCT SPECIFICATIONS

MOTOR

 

SAW

 

HP (Maximum developed)

3.0

Table Size

27-1/8” x 20-1/8”

Type

Induction

Table Extensions

Left & Right

Amps

15 / 7.5

Extension Fence Capacity

24” Left & Right

Voltage

120 / 240

Blade Size

10”

Hz

60

Rip Scale

YES

RPM (no load)

3450

Rip Fence

YES

Overload Protection

YES

Miter Gauge

YES

 

 

Maximum Cut Depth @ 90°

3-3/8”

 

 

Maximum Cut Depth @ 45°

2-1/4”

 

 

Maximum Dado Cut Width

13/16”

 

 

Net Weight

264.5 LBS

WARNING

To avoid electrical hazards, fire hazards or damage to the table saw, use proper circuit protection.

This table saw is wired at the factory for 110-120/220-240 Volt operation. It must be connected to a 110-120 Volt / 15 Ampere or 220-240 Volt / 7.5 Ampere time delay fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged in any way.

Before using your table saw, it is critical that you read and understand these safety rules. Failure to follow these rules could result in serious injury to you or damage to the table saw.

— 3 —

Page 2 Page 4
Image 3
Page 2 Page 4
Contents 10FL Hitachi Authorized Service Centers Product Specifications Motor SAWYES Check for Damaged or Loose Parts Power Tool SafetyTable SAW Safety Guidelines for Extension Cords Electrical Requirements and SafetyPower Supply Requirements Extension Cord RequirementsTools Needed Accessories and AttachmentsTools Needed for Assembly Recommended AccessoriesCarton Contents Unpacking Your Stationary Table SAW Know Your Stationary Table SAW Workpiece workpiece are edges Glossary of TermsHitachi Professional Table SAW Terms Woodworking TermsAssemble Table SAW to Stand Fig. A, B Assembly and AdjustmentsBlade Tilting Handwheel Fig. F Assembly the Table Extension Fig. CAssembly the rear table rail Fig. E Blade Raising Handwheel Fig. FTo avoid injury from an accidental start, make sure Switch is in the OFF position and the plug is disconnectedFrom the power source outlet Removing the blade guard assembly Fig. HStop Fig. JFig. K Blade Tilting Indicator Fig. LStorage Fig. O, P Rip fence and miter gauge Fig. O Installing the Table Insert Fig. NPower Cord Fig. P Mitre Gauge Adjustment Fig. QRIP Fence Adjustment Fig. R RIP Fence Indicator Fig. TRIP Fence Operation Overload Protection OperationBasic SAW Operations Tilting the BladeRipping Fig. W Bevel RippingRipping Small Pieces Mitering Fig. CC Crosscutting Fig. Y To prevent serious injuryBevel Crosscutting Fig. AA Compound Miter Crosscutting Fig. BBDado Cuts Fig. GG Auxiliary Fence Fig. EE Making the baseMaking the side Putting it togetherMaintenance Maintaining Your Table SAWLubrication Terminal Block Symptom Possible Causes Corrective Action Troubleshooting GuidePush Stick Page Parts List Parts List for Schematic aStationary Table SAW Statonary Table SAW Model NO. C10FL Schematic a Statonary Table SAW Model NO. C10FL Parts List for Schematic BStatonary Table SAW Model NO. C10FL Schematic B Hitachi Koki Canada Co
Top Page Image Contents