Panasonic SC-AK100 Using the timers, Using the play/record timer, Using the sleep timer

Using the timers

5	4
SLEEP	1 • 22 • 32
– AUTO OFF

21 • 31

Using the play/record timer

Remote control only

You can set the timer to come on at a certain time to wake you up (play timer) or to record a radio station or from the aux source (record timer).

The play and record timers cannot be used together.

Preparations:

•Turn the unit on and set the clock (A page 12).

•For the play timer, prepare the desired music source (tape/CD/ radio/aux), and set the volume.

•For the record timer, check the cassette’s erasure prevention tabs (A page 11) and insert the tape in deck 2 (A page 10). Tune to the radio station (A page 7) or select the aux source (A page 11).

1Press [CLOCK/TIMER] to select the timer function.

Every time you press the button:

CLOCK PLAY REC

Previous display rPLAY: to set the play timer

rREC: to set the record timer

2ON time setting

1(Within 8 seconds or so)

Press [g/REW/3] or [4/FF/f] to set the start time.

2Press [CLOCK/TIMER].

3OFF time setting

1Press [g/REW/3] or [4/FF/f] to set the finish time.

2Press [CLOCK/TIMER].

The start and finish times are now set.

4Press [rPLAY/REC] to display the timer indicator.

Every time you press the button:

PLAY REC

(off)

rPLAY: to turn the play timer on

rREC: to turn the record timer on

(The indicator doesn’t appear if the start and finish times or the clock hasn’t been set.)

5Press [f] to turn the unit off.

The unit must be off for the timers to operate.

•Play timer: Play will start in the set condition at the set time with volume increasing gradually to the set level.

•Record timer: Recording will start 30 seconds before the set time with the volume muted.

To cancel the timer

Press [rPLAY/REC] to clear the timer indicator from the display. (The timer comes on at the set time everyday if the timer is on.)

To change the settings (when the unit is on)

To change the play/record times

Do steps 1, 2, 3 and 5.

To change the source or volume

1.Press [rPLAY/REC] to clear the timer indicator from the display.

2.Make changes to the source or volume.

3.Do steps 4 to 5.

To change the timer

Press [rPLAY/REC] to select the desired timer. Every time the button is pressed:

PLAY REC (off)

To check the settings

Press [CLOCK/TIMER] while the unit is on to select “rPLAY” or “rREC”.

The settings are shown in the following order:

Play timer: start time→ finish time→ source→ volume

Record timer: start time→ finish time→ source

To check the settings while the unit is off, press [CLOCK/TIMER] twice.

If you use the unit after the timers are set

After using, check that the correct tape/CD are loaded before turning the unit off.

Notes

•If you turn the unit off and on again while a timer is functioning, the finish time setting will not be activated.

•If you selected AUX as the source, when the timer comes on, the unit turns on and engages “AUX” as the source. If you want to playback or record from a connected unit, set that unit’s timer to the same time. (See the connected unit’s instruction manual.)

Using the sleep timer

Remote control only

This timer turns the unit off after a set time.

While enjoying the desired source:

Press [SLEEP] to select the time (minutes).

Every time you press the button:

SLEEP 30 SLEEP 60 SLEEP 90 SLEEP 120 SLEEP OFF

To cancel the sleep timer

Press [SLEEP] to select “SLEEP OFF”.

To confirm the remaining time

Press [SLEEP] once.

The remaining time is shown for about 5 seconds.

To change the setting

Press [SLEEP] to select the new setting.

You can use the sleep timer in combination with the play/record timer. Make sure the unit is off before the play/record timer’s start time.

Note

The sleep timer will be turned off when you start recording from a CD.

13

RQT6351