Harbor Freight Tools 42933 operating instructions Unpacking, Installation

Page 6

Unpacking

When unpacking, check to make sure that all the parts are included. Refer to the Parts List and Assembly Drawing at the end of this manual. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible.

Installation

During the assembly and installation procedure, you may have to refer to the Parts List and Assembly Drawings located at the end of this manual.

1.Secure the Radial Arm Saw to a solid bench top (or table) by bolting (or clamping) the saw frame down to the bench top.

-The workbench must not be able to slide or tip over. Affix to floor if necessary.

-Position the Radial Arm Saw (or saw and bench) to slope slightly to the rear so the radial arm carriage will not roll forward due to gravity.

-The workbench should be of the appropriate length and width to allow the operator to stand aside of the saw blade, whatever position the saw blade is in.

-The work area should have adequate, overhead, non-glare lighting.

-Always lock the radial arm carriage before moving the unit.

2.Turn the Base (152) assembly upside down. Attach Table A (127) squarely to the Base assembly using the four cross-head Tapping Screws (165).

3.Attach the table stabilizer Stands to both sides of the Base using four Hex Nuts (82), Washers (149), and Round Head Bolts (148).

4.Place the Table and Base assembly on the workbench, right side up. Secure to the workbench with nuts, bolts, and washers (not supplied).

5.Position Table B (126) and Table C (125), and the rip fence (guide) and secure them by partially tightening the two screw clamps built into the Base assembly.

6.Set the Arm (118) assembly column into the Column Base. Move the Arm slightly to the left or right until the column index knob locks into the arm support column.

The arm support column has nine positive stops: 0, 15, 30, 45, and 60 degrees (left and right).

7.Attach the Elevating Handle assembly to the Arm using the Allen wrench (provided).

8.Attach the Saw Blade (17) to the Gear Shaft (19) and secure with the Outside Flange (16) and Bolt (15).

REV 03/01

SKU 42933

For replacement parts, please call 1-800-444-3353.

Page 6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents For technical questions and replacement parts, please call 42933Read all instructions before using this tool SpecificationsSafety Warnings and Precautions SKU For replacement parts, please callSKU For replacement parts, please call Safety Precautions When Using Radial Saws SKU For replacement parts, please call Installation UnpackingOperating Controls Adjustments Preparing the Work Table a SKU For replacement parts, please call Operation Cross CuttingMitre Cross Cutting Bevel Cross Cutting Compound Cross CuttingIn-Rip Cutting Out-Rip Cutting Maintenance Troubleshooting Problem Cause SolutionParts List Part Description QtyAssembly Diagram Assembly Diagram Please Read the Following Carefully

42933 specifications

Harbor Freight Tools is renowned for its extensive selection of high-quality tools and equipment at affordable prices. Among its impressive lineup, the Harbor Freight Tools 42933 stands out as a versatile and powerful solution for various cutting and grinding tasks. This tool is particularly popular among DIY enthusiasts, professional contractors, and hobbyists due to its robust performance and ease of use.

One of the main features of the Harbor Freight Tools 42933 is its powerful motor, which provides consistent performance across a wide range of applications. With variable speed control, users can easily adjust the RPM (Revolutions Per Minute) to match the specific requirements of their tasks. This feature allows for greater precision when cutting or grinding different materials, ensuring optimal results every time.

The Harbor Freight Tools 42933 also boasts a durable construction that ensures longevity and reliability. Designed to withstand the rigors of daily use, it is built with high-quality materials that resist wear and tear. The ergonomic design enhances comfort during prolonged use, reducing user fatigue and making it easier to handle intricate jobs.

The tool is equipped with advanced safety features, including an integrated safety switch that prevents accidental starts. This attention to safety is essential for users who frequently work in demanding environments where risks are prevalent. Additionally, the lightweight design allows for easy maneuverability, making it ideal for both indoor and outdoor projects.

Another remarkable aspect of the Harbor Freight Tools 42933 is its versatility. It is compatible with a wide range of accessories, enabling users to perform various applications, such as cutting wood, metal, and plastics, as well as grinding and polishing surfaces. This adaptability makes it a valuable addition to any toolbox, catering to both novice and experienced users alike.

Overall, the Harbor Freight Tools 42933 combines power, versatility, and safety features to deliver reliable performance for various tasks. Its ergonomic design and durable construction make it a top choice for those seeking an efficient tool that offers excellent value for money. Whether you're tackling home improvement projects or professional jobs, the Harbor Freight Tools 42933 is equipped to meet your needs, enhancing your efficiency and productivity.
Top Page Image Contents