690 SERIES 1-3/4 PEAK HP ROUTERS
Série 690 Toupies de 1-3/4 HP pointe
Serie 690 Rebajadoras de
Instruction manual
Manuel d'instructions
Manual de'instrucciones
www.deltaportercable.com
| INSTRUCTIVO DE OPERACIÓN, CENTROS | 690LR | |||
| 691 | ||||
| DE SERVICIO Y PÓLIZA DE GARANTÍA. | ||||
|
|
|
| LÉASE ESTE INSTRUCTIVO | 690LRVS |
|
|
|
| ||
| ANTES DE USAR EL PRODUCTO. | ||||
|
|
|
|
| 693LRPK |
|
|
|
|
| 694VK |
|
|
|
|
| 9690LR |
|
|
|
|
|
|
Part No. A22749 | Copyright © 2008 | ||||
DEFINITIONS - SAFETY GUIDELINES
indicates an imminently hazardous situation which, if not avoid- ed, will result in death or serious injury.
indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
used without the safety alert symbol indicates potentially hazard- ous situation which, if not avoided, may result in property damage.
To reduce the risk of injury, read the instruction manual.
General Power Tool Safety Warnings
Read all safety warnings and instructions Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions
for future reference
The term “power tool” in the warnings refers to your
1)Work area safety
a)Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b)Do not operate power tools in explosive atmospheres, such as in the presence of flam- mable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c)Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
2)Electrical safety
a)Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
b)Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c)Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d)Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
e)When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f)If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
3)Personal safety
a)Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious per- sonal injury.
b)Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask,
c)Prevent unintentional starting. Ensure the switch is in the off position before connect- ing to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
d)Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e)Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
f)Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g)If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust- related hazards.
4)Power tool use and care
a)Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
b)Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
c)Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such pre- ventive safety measures reduce the risk of starting the power tool accidentally.
d)Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dan- gerous in the hands of untrained users.
e)Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f)Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g)Use the power tool, accessories and tool bits etc., in accordance with these instructions taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
5)Service
a)Have your power tool serviced by a qualified repair person using only identical replace- ment parts. This will ensure that the safety of the power tool is maintained.
ADDITIONAL SPECIFIC SAFETY RULES
•Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator.
•Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.
•Metal cutting with router: If using router for metal cutting, clean out tool often. Metal dust and chips often accumulate on interior surfaces and could create a risk of serious injury, electrical shock or death.
•Keep handles dry, clean, and free from oil and grease. This will enable better control of the tool.
•Maintain firm grip with both hands on router to resist starting torque.
•Keep hands away from cutting area. Never reach under the workpiece for any reason. Keep the router base firmly in contact with the workpiece when cutting. Hold the router only by the handles. These precautions will reduce the risk of personal injury.
•Do not
•Never run the motor unit when it is not inserted in one of the router bases. The motor is not designed to be handheld.
•Keep cutting pressure constant. Do not overload motor.
•Check to see that the cord will not snag or impede the routing operation.
•Use sharp cutters. Dull cutters may cause the router to swerve or stall under pressure.
•Be sure that the motor has stopped completely before you lay the router down. If the cutter head is still spinning when the tool is laid down, it could cause injury or damage.
•Be sure that the router bit is clear of the workpiece before starting the motor. If the bit is in contact with the workpiece when the motor starts it could make the router jump, causing damage or injury.
•ALWAYS disconnect tool from power source before making adjustments or changing bits.
•Keep hands clear of bit when motor is running to prevent personal injury.
•Never touch the bit immediately after use. It may be extremely hot.
•Provide clearance under workpiece for router bit when
•Tighten collet nut securely to prevent the bit from slipping.
•Never tighten collet nut without a bit.
•Do not use router bits with a diameter in excess of
•Avoid
•Always keep chip shield (if possible) clean and in place.
extension cord
An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
Minimum Gauge for Cord Sets
|
| Volts | Total Length of Cord in Feet (meters) | |||
Ampere Rating | 120V | 25 (7.6) | 50 (15.2) | 100 (30.5) | 150 (45.7) | |
|
| 240V | 50 (15.2) | 100 (30.5) | 200 (61.0) | 300 (91.4) |
More | Not More |
|
| AWG |
|
|
Than | Than |
|
|
|
| |
|
|
|
|
| ||
0 | 6 |
| 18 | 16 | 16 | 14 |
6 | 10 |
| 18 | 16 | 14 | 12 |
10 | 12 |
| 16 | 16 | 14 | 12 |
12 | 16 |
| 14 | 12 | Not Recommended | |
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
•lead from
•crystalline silica from bricks and cement and other masonry products.
•arsenic and chromium from
Your risk from these exposure varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.
Use of this tool can generate and/or disburse dust, which may cause serious and perma- nent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.
ALWAYS wear proper personal hearing protection that conforms to ANSI S12.6 (S3.19) dur- ing use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.
ALWAYS USE SAFETY GLASSES. (ANSI Z87.1) and (CAN/CSA Z94.3) Everyday eye- glasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:
•ANSI Z87.1 eye protection (CAN/CSA Z94.3)
•ANSI S12.6 (S3.19) hearing protection
•NIOSH/OSHA/MSHA respiratory protection
SYMBOLS
The label on your tool may include the following symbols. The symbols and their definitions are as
follows: |
|
|
|
|
| |||
V | volts | A | amperes | |||||
Hz | hertz | W | watts | |||||
min | minutes |
|
| .............. | alternating current | |||
|
|
|
| direct current | no | alternating or direct current | ||
|
|
| ................ | |||||
|
|
|
| Class I Construction | no load speed | |||
|
| ..................... | ||||||
|
|
|
| |||||
|
|
|
| (grounded) |
|
|
| earthing terminal |
|
|
|
|
|
|
| ||
. | ........................ |
|
|
|
| ................ | ||
|
|
|
|
|
|
| ||
|
| ..................... | Class II Construction |
|
| ............... | safety alert symbol | |
. | ........................ |
|
| (double insulated) | BPM | beats per minute | ||
…/min | per minute | RPM | revolutions per minute | |||||
Save these instructions
MOTOR
Be sure your power supply agrees with nameplate marking. 120 Volts AC means your saw will oper- ate on alternating or direct current. As little as 10% lower voltage can cause loss of power and can result in overheating. All Porter Cable tools are
Accessories must be rated for at least the speed recommended on the tool warning label. Accessories running over rated speed can fly apart and cause injury. Accessory ratings must always be above tool speed as shown on tool nameplate.
OPERATION
To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An acci-
dental
Do not use router bits with a diameter in excess of
INSTALLING THE BIT (1001 Base)
To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An acci- dental
1.To remove the motor unit from the base unit:
(a)Open the clamp (A) Fig. 1.
(b)While holding the base, turn the power unit
(c)Lift the power unit free from the base unit.
2.Clean and insert the shank of the bit into the collet until the shank bottoms, then back it out approximately 1/16" (1.6 mm).
3.Lay the power unit on its side on a bench with the collet pointing AWAY from you.
4.Place one wrench on the flats of the chuck with the opposite end of the wrench resting on the bench to your left (Fig. 2).
5.Place the other wrench on the collet and tighten
6.To remove the bit, reverse the procedure.
Avoid possible damage to the collet. Never tighten the collet without a bit.
INSTALLING THE MOTOR (1001 base)
To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An acci-
dental
1.Open the clamp (A) Fig. 1 and set the power unit in the base unit.
2.Align the lower pin of the power unit (B) Fig. 1 with the groove in the base.
3.Rotate the power unit clockwise into the base until the upper guide pins are set in the groove of the base.
4.Close the clamp.