Porter-Cable PCB370SS instruction manual Fig. K

Page 15

Pin-end blade removal (FIG. K, L)

1.To remove the blade, loosen the tension by lifting the quick release tension lever (1). (Fig. K)

Fig. K

1

2.Remove the blade (2) from the upper (4) and lower

(5) blade holder by pulling down on the arm then pulling forward to release, and lift the blade through the access hole. (Fig. L)

Fig. L

2 4

5

3.Tilt the table to a 45° angle and lock the bevel lock knob to view lower blade holder (5-Fig. L) for removing the blade.

NOTE: Apply slight downward pressure on the upper arm when removing blade from upper blade holder.

Pin-end blade installation (FIG. M, N)

NOTE: Do not tighten the lock knobs when using Pin-end blades.

!WARNING

In order to avoid uncontrollable lifting of the workpiece, the teeth of blade should always point downward.

1.Install the blade (1) by inserting one end of it through the access hole (2) of throat plate in the table. Hook the lower blade pin in the pin recess in the lower blade holder (3) and then the upper blade pin in the upper blade holder (4). (Fig. M)

Fig. M

4

2

1

3

2.Make sure the pins are properly located in the upper

(4) and the lower (3) blade holders. (Fig. M)

3.To tension the blade (1-Fig. M), lower the quick release tension lever (5). Check the tension on the blade. If tension is too tight, turn the knob (6) counterclockwise. If tension is too loose, turn the knob (6) clockwise (Fig. N).

NOTE: If the blade is over tightened, the lever will be difficult to lower and could result in damage to the blade holder or arm assembly.

4.Tighten both upper and lower blade holder knobs.

Fig. N

5 6

BLADE GUARD FOOT ADJUSTMENT (Fig. O, P) NOTE: User must keep constant downward pressure on workpiece when cutting. The blade guard foot is not designed to hold down the workpiece, but is rather to help prevent the workpiece from lifting up excessively.

When cutting at angles, the blade guard foot (1) should be adjusted so it is parallel to the table and rests flat above the workpiece.

1.To adjust, loosen the blade guard screw (2) with hex wrench, tilt the foot so it is parallel to table and tight- en the screw.

2.Loosen the blade guard foot lock knob (3- Fig. P) to raise or lower the foot until it rests slightly above the workpiece. Tighten blade guard foot lock knob.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Catalog Number PCB370SS DE 406 MM 16 PulgProduct Specifications Table of ContentsSupport and Clamp Work Safety Guidelines DefinitionsCalifornia Proposition ProhibitionGeneral Safety Instructions Before Using this Power Tool Power Tool SafetyThink Safety Specific Safety Instructions for this Scroll SAWGuidelines for Extension Cords Electrical Requirements and SafetyPower Supply and Motor Specifications Grounding InstructionsPage Tools Needed for Assembly Unpacking Your Scroll SAW Know Your Scroll SAW Glossary of Terms Scroll SAW TermsWoodworking Terms Assembly and Adjustments Installing the Stand FIG. aMounting the Scroll SAW FIG. A, B Sawdust Collection Port FIG. E Blade Removal and InstallationMounting Scroll SAW to Work Surface FIG. C Blade Storage FIG. DFig. G PIN-END Blade Removal and InstallationFig. K Blade Selection FIG. Q Sawdust Blower FIG. POperation Freehand Cutting FIG. U Recommendations for CuttingQuantity Description Angle Cutting FIG. UInterior Cutting FIG Maintenance General MaintenanceLubrication Available Accessories Accessories and AttachmentsTroubleshooting Guide Replacement Parts Service and RepairsSymptom Possible Causes Corrective Action Parts List Parts ListSAW MM Scroll SchematicDescription Size QTY Parts List & Schematic for StandPage Warranty
Top Page Image Contents