Porter-Cable 3700L instruction manual Attaching Extension Table and Fence Slide

Page 9

ATTACHING EXTENSION TABLE AND FENCE SLIDE

1.Thread the two M8 x 1.25 x 20 Hex Head Screw into the holes (A) Fig. 4 on the left side of the saw. NOTE: Loosely tighten the hardware for further adjustment.

2.Attach the table extension (B) Figs. 4 and 5 to left side of saw table, making sure that the groove of the table extension

(B)is inside the flat washers (C) Fig. 4.

3.Use a straight edge (A) Fig. 6 to ensure that the extension table (B) is even with the saw table (D). Tighten the two screws

(C)Fig. 5.

4.Attach the fence slide support (E) Fig. 7 to the extension table (B) by using the two M8 x 1.25 x 30 socket head screws

(F). Insert the two screws up through the two holes (G) in the table extension and thread them into the two threaded holes

(H)on the bottom of the fence slide support.

NOTE: Loosely tighten the hardware for further adjustment.

5.Use a straight edge to align the fence slide support with the saw fence, and tighten the two screws.

6.Position the fence slide (K) Fig. 8 in the valley on the top of the saw fence (J) and the fence slide support (E). Move the fence slide (K) back and forth several times to check the alignment of the fence slide support (E). Make any necessary final adjustments to the fence slide support.

7.Use the 3mm hex wrench (A) Fig. 9 to thread the M6 x 1.0 x 16 set screw (B) in the fence slide support (C) to secure the extension fence.

8.Thread the fence clamping screw (N) Fig. 10 into the fence extension (E) to hold the fence extension in place.

A

B

Fig. 4

A

B

 

D

 

 

 

Fig. 6

C

B

A Fig. 9

C

B

Fig. 5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

E

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

K

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

E

 

J

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 7

 

 

 

 

 

 

 

 

 

Fig. 8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

E

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

N

 

 

 

 

 

 

 

 

Fig. 10

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

Image 9
Contents Español Página Française ManualImportant Safety Instructions Table of ContentsCalifornia Proposition Safety Guidelines DefinitionsImportant Safety Instructions General Safety RulesAdditional Safety Rules for the Laser Additional Safety Rules for Miter SawsNever Recut Small Pieces Do not Perform FREE-HAND OperationsPower Connections Motor SpecificationsGrounding Instructions Functional Description Carton ContentsUnpacking and Cleaning AssemblyAssembly Tools Required Assembly Time EstimateAttaching Extension Table and Fence Slide Operation Locking Switch in the OFF PositionAttaching the Dust BAG Fastening Machine to Supporting SurfaceDisconnect the Machine from Power Source Adjusting the Fence 90 to the BladePositive Stops Disconnect the Machine from the Power Source Rotating the Table for Miter CuttingAdjusting Sliding Fence Tilting Cuttinghead for Bevel CuttingTable Hazard Zone Adjusting the Tension of Cuttinghead Return Spring Adjusting Sliding FIT Between Cuttinghead ARM and TrunnionAdjusting 0 and 45 Bevel Positive Stops Laser USE and Adjustment Adjusting Downward Travel of SAW BladeHOW to Check Laser Alignment HOW the Lasers WorkTo Check for Vertical Alignment To Check for Rotational AlignmentTypical Operations and Helpful Hints Adjusting Lower Blade GuardGeneral Cutting Operations Auxiliary Wood FenceCutting Bowed Material Cutting AluminumRight WrongCutting Crown Moulding Crown Moulding Other AnglesTroubleshooting Maintenance Disconnect Machine from Power SourceChanging the Blade Accessories ServicePORTER-CABLE Limited ONE Year Warranty WarrantyCanadian PORTER-CABLE Delta Service Centers