Impact Wrench Kit by Wagan Tech
USER’S MANUAL — Please read before using this equipment.
________________________________________________________________________________________________________________________________________________________________
5. | Remove the vehicle’s spare tire and set it aside. |
6. | Use the vehicle’s jack to raise the vehicle. CAUTION! Refer to |
the vehicle manufacturer’s owner’s manual for instructions on using | |
the jack and to determine the proper lifting points on the vehicle. | |
Always chock the opposite wheel. | |
7. | If necessary, remove the wheel’s hubcap to expose the wheel lug |
nuts. | |
8. | Make sure the Impact Wrench is off. Then, depress the Forward/ |
Reverse Switch to its Reverse position (counterclockwise rotation). | |
9. | Insert the Socket onto the first wheel lug nut and, while |
maintaining a firm grip on the Impact Wrench with both hands, | |
squeeze the Trigger until the wheel lug nut is removed from the | |
wheel lug bolt. Release pressure on the Trigger to turn the Impact | |
Wrench off. Remove the wheel lug nut from the Socket and set the | |
lug nut aside. Then, repeat this Step to remove the remaining wheel | |
lug nuts. | |
10. Once all of the wheel lug nuts are removed, carefully remove the | |
vehicle’s flat tire and install the spare tire onto the wheel lug bolts. | |
11. Finger tighten each of the wheel lug nuts onto the wheel lug | |
bolts. | |
12. Make sure the Impact Wrench is off. Then, depress the | |
Forward/ Reverse Switch to its Forward position (clockwise rotation). | |
13. Note: Check vehicle owner’s manual for tightening sequence. | |
Insert the Socket onto the first wheel lug nut and, while maintaining a |
Impact Wrench and its accessories in the Carrying Case. Then, store the Carrying Case securely in the vehicle’s trunk.
17.If the vehicle’s cigarette lighter receptacle was used to supply electricity to the Impact Wrench, disconnect the Lead Wire Plug from the cigarette lighter receptacle. Insert the cigarette lighter back into its receptacle. Remove the Socket from the Impact Wrench. Place the Impact Wrench and its accessories in the Carrying Case. Then, store the Carrying Case securely in the vehicle’s trunk.
INSPECTION, MAINTENANCE, AND CLEANING :
1.Before each use, inspect the general condition of the Impact Wrench. Check for loose connections, cracked, or broken parts, excessively worn or damaged wiring, and any other condition that may affect the safe and proper operation of the Impact Wrench. If a problem occurs, have the problem corrected before further use. Do not use damaged equipment.
2.When cleaning, use only water and a mild detergent. Do not immerse the Impact Wrench in liquid. Do not use cleaners that are combustible or corrosive.
PRODUCT SPECIFICATIONS :
firm grip on the Impact Wrench with both hands, squeeze the Trigger | |
until the wheel lug nut is firmly tightened onto the wheel lug bolt. | |
Release pressure on the Trigger to turn the Impact Wrench off. | |
Then, repeat this Step to tighten the remaining wheel lug nuts onto | |
the lug bolts. | |
14. | Using the vehicle’s jack, slowly and carefully lower the vehicle. |
15. | If necessary, |
store the vehicle’s jack and spare tire securely in the trunk of the | |
vehicle. | |
16. | If the vehicle’s battery was used to supply electricity to the |
Impact Wrench, disconnect the Red and Black Battery Clamps from | |
the battery. Disconnect the Lead Wire Plug from the Battery | |
Clamps. Remove the Socket from the Impact Wrench. Place the |
Name
Electrical Requirements
Fuse
Torque Capacity
Drive Socket Sizes
Cords
Light
Description
12 Volt DC / 4.5 Amps
13 Amp
155
250
(17mm 19mm 21mm 23mm)
DC Cord/Plug for Cigarette Lighter Receptacle Alligator Cord/Clamps for Battery Terminal
4
© 2004 Wagan Corporation.
All Rights Reserved.
Wagan and Wagan.com are trademarks used by Wagan Corporation.
www.wagan.com