Multiquip manual HS62A CUT-OFF SAW Blades, Preparation / PRE-INSPECTION, SAW Blade Inspection

Page 18

PREPARATION / PRE-INSPECTION

1.Read and fully understand this manual, the safety instructions in particular, and the engine manufacturer's manual supplied with the saw.

2.Select the correct blade for each application. If abrasive blades are used, MAKE CERTAIN they are designed for use on a concrete floor saw. They must be reinforced and have a hole for the driving pin. When wet cutting with an abrasive blade, MAKE CERTAIN the blade is intended for wet cutting. Water will destroy a dry cut abrasive blade. Some diamond blades require water cooling and failure to do so will destroy them almost immediately. Other diamond blades can be used with or without water.

3.Handle all blades with care and NEVER use a damaged blade. NEVER use an abrasive blade that has been dropped.

BLADES

Saw blades, or cutting disks, are available in either an abrasive design or as diamond blades. Either blade will work on the HS62ACUT-OFFSAW,however,diamondbladesarerecommended. Ask your dealer about your specific cutting application.

SAW BLADE INSPECTION

WARNING

Failure to thoroughly inspect the diamond blade (Figure 12) for operational safety could result in damage to the blades or the saw and may cause injury to the user or others in the operating area.

1.Stress Relief Holes (Gullets) - Check the steel core for cracks that may have propagated from the slots and/or gullets. Cracks indicate extreme fatigue failure and if sawing continues, catastrophic failure will occur.

HS62A CUT-OFF SAW — BLADES

Figure 12. Diamond Blade

2.Edge of the Steel Core - Check the diameter edge for discoloration (blue oxidation) indicating an overheating condition caused by insufficient cooling water/air. Overheating of blades may lead to loss of core tension and/ or increase the possibility for blade failure. Make sure the steel core's width is uniform about the rim of the blade, and not succumbing to an "under-cutting" condition brought about by highly abrasive material or improper under-cutting core protection

3.Directional Arrow - Ensure that the blade is oriented properly on the blade shaft for sawing. Reference the directional arrow on the blade and place it so the direction of rotation "downcuts" with the turn of the shaft.

4.Diamond Segment or Rim - Ensure there are no cracks, dings, or missing portions of the diamond segment/rim. DO

NOT use a blade that is missing a segment or a portion of the rim. Damaged and /or missing segments/rims may cause damage to your saw or injury to the user or others in the operating area.

5.Specifications - Ensure that the blade specifications, size, and diameter properly match up to sawing operations. Utilizing a blade not matched properly to the task may result in poor performance and/or blade damage.

6.Arbor Hole - It is essential that the arbor hole diameter properly matches the blade, and that it is free from distortion. Correct blade flanges (collars) must be used. The inside face of the flanges must be clean and free of debris. An out- of-round arbor condition will cause damage to the blade and the saw.

7.MAX RPM - This RPM reference is the maximum safe operating speed for the blade selected. NEVER exceed the max RPM on the diamond blade. Exceeding the maximum RPM is dangerous and may cause poor performance and may damage the blade.

PAGE 18 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #1 (07/26/10)

Image 18
Contents SideWinder Page Page HS62A CUT-OFF SAW -TABLE of Contents Parts Ordering Procedures Best Deal! Order via Internet Dealers OnlyOrder via Fax Dealers Only HS62A CUT-OFF SAW Safety Message Alert Symbols HS62A CUT-OFF SAW Safety Message Alert Symbols Over Speed Conditions Sight and Hearing hazardSafety HS62A CUT-OFF SAW Rules for Safe OperationGeneral Safety HS62A CUT-OFF SAW Rules for Safe OperationBlade Diamond Blade Safety Saw Transportation SafetyHS62A CUT-OFF SAW Rules for Safe Operation EmergenciesHS62A Cut-off Saw Specifications Machine Operation And Safety Decals Safety Decals10 9 8 7 6 HS62A CUT-OFF SAW Controls & Components HS62A CUT-OFF SAW Blade Installation Instructions StepHex KeyTool Included withTool Kit HS62A CUT-OFF SAW -WATER KIT Installation InstructionsSocket Head Cap Screw w/ Washer  Front HandleBlades HS62A CUT-OFF SAW BladesPreparation / PRE-INSPECTION SAW Blade InspectionFuel Check HS62A CUT-OFF SAW Initial START-UP/OPERATIONInitial START-UP StartingOperation Shut-downBelt Changing Procedure Belt Guard Cover RemovalHS62A CUT-OFF SAW Maintenance Reversing the Cutting Arm Procedure Tool KitReconnect the guard adjustment knob  HS62A CUT-OFF SAW Maintenance AIR/FUEL Filter Air/Fuel Filter Maintenance ProceduresHS62A CUT-OFF SAW Troubleshooting Blade HS62A CUT-OFF SAW Troubleshooting Engine Troubleshooting EngineTroubleshooting Engine Symptom Possible Cause SolutionDRY Filter Kits HS62A CUT-OFF SAW Filter KitsHS62A CUT-OFF SAW Explanation of Parts Section Remarks QTY. ColumnHS62A CUT-OFF SAW Suggested Spare Parts To 3 UnitsHS62A CUT-OFF SAW Muffler Assy Part Name HS62A CUT-OFF SAW Recoil Start Assy HANDLE, Starter Rope HS62A CUT-OFF SAW Crankcase Assy Plate HS62A CUT-OFF SAW V-BELT Cover Clutch Side Assy Belt COVER, Clutch Side HS62A CUT-OFF SAW V-BELT Cover Pulley /BLADE Guard Assy HS62A CUT-OFF SAW V-BELT Cover Pulley /BLADE Guard Assy HS62A CUT-OFF SAW Fueltank Assy Part Name QTY Remarks HS62A CUT-OFF SAW Lifting Handle and Roller Assy Handle HS62A CUT-OFF SAW -THROTTLE Linkage Assy Spring HS62A CUT-OFF SAW Flywheel Cover Assy WASHER, Flat HS62A CUT-OFF SAW Flywheel Assy Pawl SET HS62A CUT-OFF SAW Ignition Coil Assy Spring Spark Plug HS62A CUT-OFF SAW AIR Filter Assy FLANGE, PRE- FILTER, CAP HS62A CUT-OFF SAW Carburetor Mounting Assy Carburetor Mounting Assy HS62A CUT-OFF SAW Carburetor Assy Throttle Shaft HS62A CUT-OFF SAW Crankshaft / Piston Assy HS62A CUT-OFF SAW Crankshaft and Piston Assy RING, Piston PINHS62A CUT-OFF SAW Water KIT Assy VALVE, SHUT-OFF HS62A CUT-OFF SAW Cart Assy HS62A CUT-OFF SAW Cart Assy HS62A CUT-OFF SAW Tools HS62A CUT-OFF SAW Tools Recommended Diamond Blades For Your Side Winder Saw HS62A CUT-OFF SAW Recommended Diamond BladesTerms and Conditions of Sale Parts HERE’S HOW to GET Help
Related manuals
Manual 68 pages 60.02 Kb