Multiquip HS62A manual Belt Changing Procedure, Belt Guard Cover Removal

Page 21

HS62A CUT-OFF SAW — MAINTENANCE

V-Belt Changing Procedure

N

Remove the 2 hex nuts and hex screw and washer to gain access to the V-belt on the clutch side. Remove V-belt cover .

Figure 14. Belt Guard Cover Removal

Remove the 2 hex nuts and hex screw and guard adjustment knob to gain access to theV-belt on the spindle side. Remove the Cover Guard .

Figure 15. Re-Installing Cover Guard

Using the provided wrench, loosen the three nuts to reduce the tension on the V-belt, then turn the V-beltTensioning Cam until the V-belt is completely slacked.

Figure 16. V-BeltTensioning

Remove the V-belt from the clutch and spindle pulleys. Install the new V-belt around both pulleys. It is essential that the drive V-belt is properly positioned around both the clutch and spindle pulleys.

Figure 17. DriveV-Belt

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #1 (07/26/10) — PAGE 21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents SideWinder Page Page HS62A CUT-OFF SAW -TABLE of Contents Parts Ordering Procedures Best Deal! Order via Internet Dealers OnlyOrder via Fax Dealers Only HS62A CUT-OFF SAW Safety Message Alert Symbols Over Speed Conditions Sight and Hearing hazard HS62A CUT-OFF SAW Safety Message Alert SymbolsHS62A CUT-OFF SAW Rules for Safe Operation SafetyGeneral Safety HS62A CUT-OFF SAW Rules for Safe OperationBlade Saw Transportation Safety Diamond Blade SafetyEmergencies HS62A CUT-OFF SAW Rules for Safe OperationHS62A Cut-off Saw Specifications Safety Decals Machine Operation And Safety Decals10 9 8 7 6 HS62A CUT-OFF SAW Controls & Components Step HS62A CUT-OFF SAW Blade Installation InstructionsSocket Head Cap Screw w/ Washer  HS62A CUT-OFF SAW -WATER KIT Installation InstructionsHex KeyTool Included withTool Kit Front HandlePreparation / PRE-INSPECTION HS62A CUT-OFF SAW BladesBlades SAW Blade InspectionInitial START-UP HS62A CUT-OFF SAW Initial START-UP/OPERATIONFuel Check StartingShut-down OperationBelt Guard Cover Removal Belt Changing ProcedureHS62A CUT-OFF SAW Maintenance Tool Kit Reversing the Cutting Arm ProcedureReconnect the guard adjustment knob  Air/Fuel Filter Maintenance Procedures HS62A CUT-OFF SAW Maintenance AIR/FUEL FilterHS62A CUT-OFF SAW Troubleshooting Blade Troubleshooting Engine HS62A CUT-OFF SAW Troubleshooting EngineSymptom Possible Cause Solution Troubleshooting EngineHS62A CUT-OFF SAW Filter Kits DRY Filter KitsQTY. Column HS62A CUT-OFF SAW Explanation of Parts Section RemarksTo 3 Units HS62A CUT-OFF SAW Suggested Spare PartsHS62A CUT-OFF SAW Muffler Assy Part Name HS62A CUT-OFF SAW Recoil Start Assy HANDLE, Starter Rope HS62A CUT-OFF SAW Crankcase Assy Plate HS62A CUT-OFF SAW V-BELT Cover Clutch Side Assy Belt COVER, Clutch Side HS62A CUT-OFF SAW V-BELT Cover Pulley /BLADE Guard Assy HS62A CUT-OFF SAW V-BELT Cover Pulley /BLADE Guard Assy HS62A CUT-OFF SAW Fueltank Assy Part Name QTY Remarks HS62A CUT-OFF SAW Lifting Handle and Roller Assy Handle HS62A CUT-OFF SAW -THROTTLE Linkage Assy Spring HS62A CUT-OFF SAW Flywheel Cover Assy WASHER, Flat HS62A CUT-OFF SAW Flywheel Assy Pawl SET HS62A CUT-OFF SAW Ignition Coil Assy Spring Spark Plug HS62A CUT-OFF SAW AIR Filter Assy FLANGE, PRE- FILTER, CAP HS62A CUT-OFF SAW Carburetor Mounting Assy Carburetor Mounting Assy HS62A CUT-OFF SAW Carburetor Assy Throttle Shaft HS62A CUT-OFF SAW Crankshaft / Piston Assy RING, Piston PIN HS62A CUT-OFF SAW Crankshaft and Piston AssyHS62A CUT-OFF SAW Water KIT Assy VALVE, SHUT-OFF HS62A CUT-OFF SAW Cart Assy HS62A CUT-OFF SAW Cart Assy HS62A CUT-OFF SAW Tools HS62A CUT-OFF SAW Tools HS62A CUT-OFF SAW Recommended Diamond Blades Recommended Diamond Blades For Your Side Winder SawTerms and Conditions of Sale Parts HERE’S HOW to GET Help
Related manuals
Manual 68 pages 60.02 Kb
Top Page Image Contents