Charge-It-All Sport Safety Features, Lithium Mode

Charge-It-All Sport Safety Features:

● Choose the charge type (either NiMH, NiCD or Lithium) by pressing

● If the battery pack polarity is reversed or if the battery pack has a short circuit,

and holding the MODE button for

1.5 seconds. The charge mode

the charger will shut off and the charge rate LEDs will blink together. If this

will change as indicated by the

happens, unplug the battery pack from the charger and double-check all wires

green LED. If your battery has

for polarity and short circuits before reattaching the battery pack to the charger.

NiCD cells, choose the NiCD

● When the START/STOP button is pressed to start the charging process,

charge mode. If your battery has

an internal safety timer is automatically started. If the battery pack

NiMH cells, choose the NiMH

malfunctions or misses the “peak,” the timer will automatically stop the

charge mode.

If you have a

charging process after the following elapsed times:

Lithium Polymer (LiPO) battery,

NiCD and NiMH MODE

choose the Lithium charge mode.

WARNING

Always make sure that you choose the charge mode that

Amp .................. 300 Minutes

matches the type of cells in your battery pack. Charging your battery pack

Amps ................. 150 Minutes

using a charge mode that’s different than the cell type you’re charging will

Amps ................. 100 Minutes

damage the battery pack and possibly result in fire.

Amps ................... 75 Minutes

● After selecting the charge

Amps ................... 50 Minutes

LITHIUM MODE

mode, select the charge rate by

briefly pressing the MODE

All Amp Ratings ........... 3 Hours

button until the desired charge

After the charge process is complete, the charger switches

rate is selected as indicated by

the blinking red LED. See the

to trickle charge mode at 1/10th of the selected charge rate,

table below for recommended

regardless of the charge mode

charge rates.

Using Your Charge-It-All Sport Charger:

Recommended Charge Rates

We recommend choosing a charge rate for NiMH batteries that is close to

Before using your charger for the first time, please read and

the batteries’ rated mAH capacity (e.g., charge a 2000mAH NiMH battery

understand the warnings listed on the front page. Failure to

at no more than 2 amps). For NiCD batteries, we recommend choosing a

understand and follow these warnings can result in damage to the

charge rate that is 1-3 times the batteries’ rated mAH capacity (e.g., charge

charger, your flight battery or worse.

a 1400mAH NiCD battery at 2-4 amps).

● Plug the desired input cord into the back of the charger (either 12V DC

NiCD Charge Rates

NiMH Charge Rates

or 110V AC), then plug the input cord into the power source. The red and

green LEDs will default to the position they were in when the charger was

1000mAH

1A -3 A

1000mAH

last used.

1200mAH

2A - 3A

1200mAH

1400mAH

2A - 4A

1400mAH

1600mAH

2A - 5A

1600mAH

1A - 2A

1800mAH

2A - 5A

1800mAH

1A - 2A

2000mAH

2A - 6A

2000mAH

2400mAH

3A - 6A

2400mAH

2800mAH

3A - 6A

2800mAH

3000mAH

3A - 6A

3000mAH

WARNING Never plug the charger into a 220V power source and never

Lithium Charge Rates

145mAH

.1A (100mAH)

1250mAH

1.3A

connect the charger to a 12V DC and a 110V AC power source at the

same time. Use only one desired power source at a time. If connecting

340mAH

.3A (300mAH)

1500mAH

1.3A

the charger to a 12V DC power source, make sure to attach the red

350mAH

.3A (300mAH)

2000mAH

alligator clip to the positive terminal and the black alligator clip to the

520mAH

.3A (300mAH)

2100mAH

negative terminal.

750mAH

.7A (700mAH)

2150mAH

● Plug the banana plugs on the output cord into the front of the charger,

830mAH

.7A (700mAH)

2500mAH

making sure that the polarity is

910mAH

.7A (700mAH)

3200mAH

correct (red to red and black to

1050mAH

.7A (700mAH)

4000mAH

black), then connect your

Sample average charge time for a 1600mAH battery charged at:

battery to the output cord.

1Amp is 96 minutes

1000mA in 1A

IMPORTANT If the connector on

2Amps is 48 minutes

1600/4000=0.4x60=24 Minutes

your battery is different from the

4Amps is 24 minutes

connector on the output cord,

IMPORTANT Batteries may be charged at different rates depending on

you will need to change the

the manufacturer’s suggestions. The table above is for general reference

connector on the output cord. If you do, double-check that the polarity is

only and errs on the side of caution.

correct when you install your new connector.

NOTE The charger includes a JST adapter if your battery uses a JST

IMPORTANT If you are charging 8 cells using a 12V DC power source,

plug. The JST plug is typically referred to as a BEC connector and is red.

the DC input (your power source) MUST be higher than 14V.

Continued On Back Page ☛