Vanson V-6000 manual White paper

Page 43

+/- button

Using the Custom White Balance

White balance settings may vary slightly depending on the shooting environment.

You can select the most appropriate white balance setting for a given shooting environment by setting up the custom white balance.

1.Select the CUSTOM ( ) menu of the White Balance.

2.Place a sheet of white paper in front of the camera so that the LCD monitor shows only white, and then press the SHUTTER button.

3.Your custom white balance value is stored.

-The custom white balance value will be applied, starting with the next picture you take.

-The user configured white balance will be remain effective until it is overwritten.

MEASURE:SHUTTER

[ White paper ]

Exposure compensation : This camera automatically adjusts the exposure according to the ambient lighting conditions.

You can also select the exposure value by using the +/- button.

Compensating Exposure

1. Press the +/- button, and then use the UP and DOWN buttons to select the exposure compensation icon ( ). The exposure compensation menu bar will appear as shown.

2. Use the LEFT and RIGHT buttons to set the desired exposure compensation factor.

3.Press the +/- button again. The value you set will be

saved and the Exposure Compensation setup mode will close. If you change the exposure

value, the exposure indicator ( ) will be displayed on the bottom of the LCD monitor.

*A negative exposure compensation value reduces the exposure.

Note that a positive exposure compensation value increases the exposure and the LCD monitor will appear white or you may not get good pictures.

43

Image 43

Contents

English Instructions Contents Dpof Dpof Standard FAQDpof Index Dpof Print Size About the icons Getting to know your cameraPage An FCC warning Viewing images on a TV. refer to This digital camera can be used forEditing images on a PC Refer to This digital camera can be used for Manufacturers contents MF / Delete Identification of featuresFront & Top Back & BottomMENU/ OK Mode dialFLASH/ Left SELF-TIMER Side/ 5-function buttonImage size Sunset Mode SceneMode PlayCR-V3 type Lithium Rechargeable batteries AA type Connecting to a Power SourceImportant information about battery usage AA typeArrow Polarity+Insert the batteries taking note of the polarity + Instructions on how to use the memory card Mode Still Image mode Movie Clip mode Removing the memory card Inserting the memory cardIcons LCD monitor indicator000130 Starting the recording modeSelect the Auto mode by rotating the mode dial ISOStarting the recording mode Will switch to the settings you changed in Step How to use the MySET modeMenu buttons to change the desired camera Functions Movie clip recording As the available recording timeAgain Scene mode Things to Watch Out for When Taking Pictures Zoom W/T button Using the camera buttons to adjust the cameraZoom T button will have no effect Zoom W/T buttonSubject will appear nearer Digital zoom TeleVoice memo / UP button Voice memo / UP button Take a picture with the desired macro modeMacro / Super Macro button O O O X X X X X X X X O O O X X X X O X X X Types of focus modes and focus ranges W WIDE, T Tele Unit mNormal Macro Super Macro Range W0.3~0.8 T0.3~0.8 W0.06~0.3 Auto O O O O O O O OImage to be captured Focus lockISO Autofocus Macro Wide Tele Flash / Left buttonIcon Self-timer/ remote mode definition Icon Mode SELF-TIMER / Remote buttonMovie Clip Auto ProgramVoice Recording Memu button MENU/ OK buttonMF button 1st part 8m ~ infinity MF button Exposure compensation ~0.0~+2.00.5EV steps +/- buttonSub menu RGB+/- button White paper Fast Slow SmallShutter Speed LCD button Metering Multi Spot Using the LCD monitor to adjust the camera settingsCamera working mode Tiff FineDawn ShootingShots Normal Effect Sepia SoftIcon 2816 2560 2272 2048 1600 1024 640 320 How to use the menuSize Use the UP and Down buttons to select a sub menuTiff QualityJpeg Continuous shot MeteringSingle Negative Continuous shotEffect NormalVivid SharpnessFireworks ScenePortrait ChildrenStarting play mode To play back a Clip, the movie clip indicatorPlaying back a movie clip ImagePlaying back a recorded voice Flash OFF SizeDate Thumbnail / Enlargement button Voice memo 2272 2048 1600 1024 640Temporarily stops playback Pause mode Resumes playbackPlay & Pause button Button againLCD button Delete button Setting up the play back function using the LCD monitor Photo Menu tab Main menu Sub menu Secondary menuONE PIC TypeIndex Dpof Print ResetFine Custom SET File Name OFF PrintStarting the slide show Protecting images CancelDeleting images Protecting imagesImage Resize Types Size 1600X1200 1280X960 800X600 ResizeButton and press the OK button LogoRight Left Rotating an imageFormat Press the LEFT/ Right button and select the Dpof menu tabDpof Size secondary menu CANCEL, 3X5, 4X6, 5X7 Setting the Print SizeDpof Auto Print Printer SetupPictBridge ImagesUse the UP and Down buttons to select the desired PictBridge Picture SelectionPrinter.See p.86 Images menu will appearAUTO, OFF, on PictBridge Print SettingAuto SET AUTO, DRAFT, NORMAL, FineStandard PictBridge PrintingReset PictBridge ResetIf no is selected Settings will not be reset Setup menu 3SEC Reset YES USB Computer PrinterFile name Bright Video Ntsc PAL View OFFFile name Auto power offFormatting a memory card LanguageImprinting the recording date Setting up the Date/ Time/ Date typeSound Operation status Setting Operation SoundsLCD brightness Selecting Video out type Quick view InitializationRESET ALLSelect this if you want to connect the camera to your PC Connecting an External Device USBPrinter Turned on Setting a Startup Image Setting up the Mycam menuStart up image Shutter sound Start up soundImportant notes Important notes Card Full Card ErrorFile Error LOW BatteryBefore contacting a service center Clean the lens Symptom Causes RemedyMacro shot mode Mode UnclearCamera External monitor When usingCheck the connection cables No image onSpecifications World Unique 9 Different Power Source Dimensions WxHxDDigimax Viewer, ArcSoft PhotoImpression System Requirements Software NotesAbout the software Setting up the application software About the application program Refer to page 98 for more informationClick the OK button Select Components window will appear. Click Next button 103 104 Button and press the Right button Starting PC ModeCut 107 Removing the USB Driver for Windows 98SE Removable Disk Important information whilst using the Removable DiskRemoving the removable disk Using the USB Driver for MAC Setting up the USB Driver for MACUsing PhotoImpression This software is only compatible with Windows Digimax ViewerProperty SpecificationUse a USB cable with the correct specification Digimax ViewerThen turn on the camera Case Manager Install the camera driver correctlyTab and then click Update Driver or Reinstall Driver USB interface Case When using the USB hubSettings Control Trace Start Programs Memo 119 6806-2210