Northern Industrial Tools 2 HP / 8 GALLON AIR COMPRESSOR instruction

OPERATION

BEFORE OPERATING YOUR NEW AIR COMPRESSOR please check the following points carefully:

1 Check that all nuts and bolts are secure.

2. Make sure oil has been properly added to compressor. (See Installing Oil and Oil Breather Cap section.)

Initial Start-Up Procedure

1. Open the Air Tank Drain Valve to permit air to escape, preventing air pressure buildup in the air tank.

2. Run the compressor for a minimum of 20 minutes in this “no-load” position to lubricate the piston and bearings.

3. Close Air Tank Drain Valve. Your compressor is ready for use.

Depending on the CFM draw of the tools being operated, your new Air Compressor can be used for operating paint sprayers, air tools, grease guns, airbrushes, caulking guns, abrasive blasters, tire & plastic toy inflation, spraying weed killer and insecticides, etc. Proper adjustment of the Air Pressure Regulator is necessary for all of these operations. Refer to the air pressure specifications provided with the tool you are using.

General Overview

To compress air, the piston moves up and down in the cylinder. On the down stroke air is drawn in through the valve inlet. The discharge valve remains closed. On the upstroke of the piston air is compressed. The inlet valve closes and air is forced out through the discharge valve, through the check valve, and into the air tank. Working air is not available until the compressor has raised the tank pressure above that required at the air service connection. The air inlet filter openings must be kept clear of obstructions, which could reduce air delivery of the compressor.

Installation and Location

Locate the compressor in a clean, dry and well ventilated area. The compressor should be located 12 to 18 inches from walls or any other obstruction which would interfere with airflow. Compressor should be loacted in a temperature controlled area between 32º and 95º fahrenhert. Place the compressor on a firm, level surface. The compressor is designed with heat dissipation fins which allow for proper cooling. Keep the fins (and all other parts which collect dust or dirt) clean. A clean compressor runs cooler and provides longer service. Do not place rags, containers or other material on top of the compressor.

Connecting to Power Source

This air compressor is designed to operate on a properly grounded 120 volt, 60Hz, single phase, alternating current (ac) power source with a fused 20 amp time delayed fuse or circuit breaker. It is recommended that a qualified electrician verify the ACTUAL VOLTAGE at the receptacle into which the unit will be plugged and confirm that the receptacle is properly fused and grounded. The use of the proper circuit size can eliminate nuisance circuit breaker tripping while operating your air compressor.

Extension Cords

For optimum Air Compressor performance an extension cord should not be used unless absolutely necessary. If necessary, care must be taken in selecting an extension cord appropriate for use with your specific Air Compressor. Select a properly grounded extension cord which will mate directly with the power source receptacle and the Air Compressor power cord without the use of adapters. Make certain that the extension cord is properly wired and in good electrical condition. Maximum length of extension cord should be 50 feet. Minimum wire size of extension cord should be 12 gauge.

Attaching an Air Hose

Your Air Compressor is supplied with a 1/4" Quick Disconnect Air Chuck. Once you have correctly installed the Air Chuck (See Installing the Air Chuck on p.4) your compressor will be ready to accept air hoses equipped with 1/4" male air couplers.

Note: Use only air hoses rated for use with 115psi air pressure or higher.

To install an air hose, equipped with a 1/4" male coupler:

1. Pull back on Air Chuck outer sleeve to allow coupler to be fully inserted into Air Chuck.

2. Insert coupler into Air Chuck.

3. Release outer sleeve of Air Chuck.

4. Verify that air hose is securely connected to Air Chuck by pulling lightly on air hose.

(See Figure 6)

Figure 6. Attaching an Air Hose

2 HP / 8 GALLON AIR COMPRESSOR specifications

The Northern Industrial Tools 2 HP / 8 Gallon Air Compressor is a versatile and reliable solution for a variety of air-powered applications. Designed with both performance and portability in mind, this air compressor is ideal for professionals and DIY enthusiasts alike. With a robust 2 horsepower motor, it delivers impressive power to meet the demands of numerous pneumatic tools.

One of the standout features of this compressor is its 8-gallon horizontal tank. This tank capacity strikes a perfect balance between maintaining steady air pressure and minimizing the physical footprint of the unit. The tank is constructed from durable steel, ensuring long-lasting performance and resistance to corrosion. The horizontal design facilitates stability and makes it easier to transport around job sites or workshops.

Equipped with a powerful oil-free pump, the Northern Industrial Tools air compressor requires minimal maintenance while providing reliable performance. The oil-free design eliminates the need for regular oil changes and reduces the risk of contamination, making it suitable for environments where moisture and oil-free air are essential. This feature also contributes to its overall efficiency, as it runs cooler and quieter than many traditional compressors.

The compressor operates at a maximum pressure of 125 PSI, providing ample power for a range of tasks such as inflating tires, operating nail guns, and powering air tools. The unit features a dual-gauge setup, which allows users to monitor both the tank and outlet pressure at a glance, ensuring optimal performance and safety during operation.

Another notable characteristic is its portable design, which includes a sturdy carrying handle and wheels for easy maneuverability. Weighing approximately 60 pounds, it strikes a balance between being lightweight enough for transport and sturdy enough for heavy-duty use.

Safety features such as a thermal overload protector help prevent overheating, adding an extra layer of reliability. Moreover, the compressor is equipped with a quick-connect air hose coupling system that simplifies attaching and detaching air tools, allowing for seamless transitions between tasks.

In summary, the Northern Industrial Tools 2 HP / 8 Gallon Air Compressor is a powerful, portable, and maintenance-friendly solution that meets the diverse needs of air-powered applications. Its combination of features, including an oil-free pump, robust tank, and user-friendly design, make it an excellent choice for both home workshops and professional job sites.