Porter-Cable FC350 EMPLOYER’S Responsibilities, Functional Description, Foreword, Power Source

Page 7

EMPLOYER’S RESPONSIBILITIES

Employer must enforce compliance with the safety warnings and all other instructions contained in this manual.

Keep this manual available for use by all people assigned to use this tool.

For personal safety and proper operation of this tool, read and understand tool labels and manual. Failure to follow warnings could result in DEATH or SERIOUS INJURY. Read and follow all of these instructions carefully.

FUNCTIONAL DESCRIPTION

FOREWORD

Porter-Cable Model FC350 is a heavy duty pneumatic framing nailer. It is designed to install .113" to .131" diameter, clipped head, paper-tape collated framing nails of various lengths from 2" to 312". Fastener collation angle is 34°.

Use approved Porter-Cable fasteners only.

POWER SOURCE

This tool is designed to operate on clean, dry, compressed air at regulated pressures between 70 and 120 PSI (Pounds per Square Inch)(4.8 to 8.3 BAR). The preferred system would include a filter, a pressure regulator, and an automatic oiler located as close to the tool as possible, within 15 ft/4.6 m is ideal.

All compressed air contains moisture and other contaminates that are detrimental to internal components of the tool. An air line filter will remove most of these contaminates and significantly prolong the life of the tool. If an in-line oiler is not available: place five or six drops of Porter-Cable Air Tool Oil into the tool’s air inlet at the beginning of each workday.

The tool is equipped with a 1/4" male “quick connector”. A 3/8" male “quick connector” is available from Porter-Cable and may be used in situations where a 1/4" supply line is not available. A 3/8" supply line (and fittings) are required for maximum tool performance. The tool must always be connected to the air supply with a coupling such that all pressure is removed from the tool when the coupling is disconnected.

All air line components (hoses, connectors, filters, regulators, etc.) must have a minimum working pressure rating of at least 150 PSI (10.3 BAR) or 150% of maximum system potential, whichever is greater.

Do not connect tool to pressure which potentially exceeds 200 PSI (13.7 BAR).

Only connect tool to air supply hose with a coupling that automatically removes all pressure from the tool when the coupling is disconnected.

Disconnect tool from air supply before performing maintenance, clearing a jammed fastener, leaving work area, moving tool to another location, or handing the tool to another person.

PREPARING THE TOOL

1.After reading and understanding this entire manual, connect tool to

air supply (Fig. 18).

Never point tool at yourself or others.

Always connect tool to air supply before loading fasteners (Fig. 18).

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Instruction Clipped Head Manual Framing Nailer Portercable Important Safety Instructions Safety Guidelines / DefinitionsGeneral Safety Rules Page Technical Specifications Foreword Power SourceEMPLOYER’S Responsibilities Functional DescriptionPage Operating Instructions Using the Tool with Selectable Triggering OptionsPage Clearing a Jammed Fastener Clean and Inspect Daily MaintenanceService and Repairs Accessories TroubleshootingPORTER-CABLE Limited ONE Year Warranty Canadian PORTER-CABLE Delta Service Centers

FC350 specifications

The Porter-Cable FC350 is a versatile and robust finishing nailer designed for professionals and DIY enthusiasts who demand performance and reliability in their tools. Known for its efficient power and features, the FC350 has become a staple in various applications, particularly in trim work, cabinetry, and furniture assembly.

One of the standout features of the FC350 is its lightweight design, which enhances maneuverability while reducing operator fatigue during extended use. Weighing in at just under 6 pounds, it is easy to handle and position successfully, making it ideal for overhead and awkward angles. The ergonomic handle provides a comfortable grip, further enhancing its usability in challenging conditions.

The FC350 operates using a reliable and efficient pneumatic system, requiring an air compressor to function. It boasts a firing speed of up to 10 nails per minute, allowing for quick and efficient completion of projects. The depth adjustment feature enables users to control how deep the nails are driven, providing greater precision and adaptability to various materials. This is essential when working with different types of trim or when delicate work is involved.

Another notable characteristic of the FC350 is its 360-degree exhaust system that directs air away from the operator and the work surface. This not only keeps the workspace clean but also enhances safety by reducing the risk of debris and dust impacting the nailer's performance.

The tool features a tool-free jam release mechanism, enabling users to quickly and easily clear any jams that may occur without the need for additional tools. This quick access to the nail compartment ensures minimal downtime, allowing for more efficient work.

The FC350 is compatible with 18-gauge nails ranging from 1 to 2 inches in length, making it suitable for a wide range of fastening applications. It also features a sequential firing mode for greater control, ensuring precise placement even in intricate projects.

In summary, the Porter-Cable FC350 finishing nailer stands out for its combination of lightweight design, powerful pneumatic operation, convenient features, and versatility. It's a reliable choice for anyone looking to achieve professional-grade results in finishing applications. Whether you are a seasoned contractor or a weekend warrior, the FC350 will enhance productivity and deliver superior results on every project.
Top Page Image Contents