Grizzly G0588/G0591 instruction manual Lubrication, Sliding table ways

Page 46

Lubrication

The bearings are sealed and pre-lubricated and require no lubrication during their usable life. However, your saw components will operate at their best if the bearing surfaces are kept clean—this is especially important for the trun- nion bearings.

Lubricate the areas indicated below every 6-12 months, depending on frequency of use.

1.Blade angling pivots. These should be lubricated with 6 or 7 drops of light machine oil (see Figure 77).

Blade Angling

Trunnion

Figure 77. Blade angling trunnions.

2.Sliding table ways. Spray or wipe on a light machine oil or lubricant such as Boeshield T9® the entire length of the steel rods (see Figure 78).

3.Blade height worm gears. Lubricate with an automotive wheel bearing grease (see Figure 79).

Blade Height

Worm Gear

Blade Tilt

Worm Gear

Figure 79. Gear lubrication.

4.Blade tilt worm gear. Lubricate with an automotive wheel bearing grease.


	Figure 78. Sliding table ways.
-44-		G0588/G0591 12" Sliding Table Saws

Image 46

Contents Sliding Table SAW Model G0588/G0591Page Table of Contents Operations Foreword IntroductionContact Info Machine Data Sheet Identification Power ON/OFF Buttons Turns the mainBlade Angle Handwheel Adjusts the angle Emergency Stop Button TurnsPage Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Sliding Table Saws Protecting Yourself From Kickback Preventing KickbackBelow are tips to reduce the likelihood of kickback Glossary of Terms 220V Single-Phase Circuit Requirements220/440V 3-Phase WiringPhase Converter Rewiring to Grounding Control panel cover plate G0588/G0591 12 Sliding Table SawsMagnetic switch Items Needed for Set Up SET UPSet Up Safety Unpacking Description QtyMoving & Placing Base Unit Site ConsiderationsClean Up Inventory Crate Qty Saw Base Unit Not ShownBlade guard components Edge Shoe Hold Down Hardware and ToolsHardware Recognition Chart Sliding Table To install the sliding tableComponents and Hardware Needed Qty To install the extension tables Extension TablesTo install the rip fence Rip Fence and ScalePage To install the blade Main BladeTo install the scoring blade Scoring BladeRiving Knife Alignment Aligning BladesTo align the blades and riving knife Page To adjust the sliding table parallel with the main blade Sliding Table ParallelismCrosscut Table To install the crosscut tableTo install the crosscut fence Crosscut FenceFence Scale Alignment To align the fence scale with the bladeTo connect the saw to the power source Power CordTest Run Operations Operation Safety Operation TipsPlease follow these tips Every time you use your saw Changing Blades Rip Cutting Rip cutting with the sliding tableRip cutting using traditional table saw techniques Crosscutting Crosscutting full size panels Fence to Blade on Page 48 if necessaryMiter Cutting To perform a miter cutG7895-Citrus Degreaser AccessoriesG1955-OxiSolvBlade & Bit Cleaner G5562-SLIPIT1 Qt. Gel G5563-SLIPIT12 oz SprayH1300 H1298 G7984 H2347 H0736 H6460-12 Tooth Scoring Blade SetH3771-Blade Loc H3308-SHOP FOX Push StickG3445-Precision Saw Tool G7581-Superbar G7582-Master PlateSchedule MaintenanceCleaning Unpainted Cast IronLubrication Sliding table waysAbout Service ServiceReplacing Belts Page Blade Tilt Squaring Crosscut Fence to Blade To square the crosscut fence with the bladeG0591 single phase magnetic switch Contactor Overload Relay ElectricalTroubleshooting Symptom Possible Cause Possible SolutionLoud repetitious noise coming Parts Main BodyG0588/G0591 12 Sliding Table Saws PW01M Flat Washer 8MM PSB02M CAP Screw M6-1 X Saws Sliding Table G0588/G0591 12 Sliding Table Saws PN03M G0588/G0591 12 Sliding Table Saws PN01M HEX NUT M6-1 G0588/G0591 Rip Fence G0588/G0591 12 Sliding Table Saws Tilt Assembly G0588/G0591 12 Sliding Table Saws Motor Assembly PK42MG0588/G0591 12 Sliding Table Saws Arbor Assembly G0588/G0591 12 Sliding Table Saws Warranty and Returns Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAPage Call Today For a Free Full Color Catalog