Grizzly G0588/G0591 instruction manual About Service, Replacing Belts

Page 47

SECTION 7: SERVICE

Always disconnect power to the machine before performing ser- vice adjustments. Failure to do this may result in serious personal injury.

About Service

This section is designed to help the operator with adjustments that were made at the factory and that might also need to be made during the life of the machine.

This section is provided for your convenience— it is not a substitute for the Grizzly Service Department. If any adjustments arise that are not described in this manual, then feel free to call the Grizzly Service Department at (570) 546-9663.

Similarly, if you are unsure of how to perform any procedure in this section, the Grizzly Service Department will be happy to guide you through the procedures or help in any other way.

Replacing Belts

To ensure optimum power transmission from the motor to the blades, the belts must be in good condition (free from cracks, fraying and wear) and operate under proper tension.

To change the main blade arbor V-belt:

1.Disconnect the saw from the power source!

2.Move the blade tilt to 45˚, lower the main blade all the way down, and open the motor cabinet door.

3.Loosen the belt tension bolt (Figure 80) and pivot the motor up.

Figure 80. V-belt tension bolt.

G0588/G0591 12" Sliding Table Saws

-45-

Image 47

Contents Model G0588/G0591 Sliding Table SAWPage Table of Contents Operations Contact Info IntroductionForeword Machine Data Sheet Emergency Stop Button Turns Power ON/OFF Buttons Turns the mainBlade Angle Handwheel Adjusts the angle IdentificationPage Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Sliding Table Saws Below are tips to reduce the likelihood of kickback Preventing KickbackProtecting Yourself From Kickback Glossary of Terms Circuit Requirements 220V Single-PhaseWiring 220/440V 3-PhaseControl panel cover plate G0588/G0591 12 Sliding Table Saws Phase Converter Rewiring to GroundingMagnetic switch Description Qty SET UPSet Up Safety Unpacking Items Needed for Set UpSite Considerations Moving & Placing Base UnitCrate Qty Saw Base Unit Not Shown Clean Up InventoryHardware and Tools Blade guard components Edge Shoe Hold DownHardware Recognition Chart Components and Hardware Needed Qty To install the sliding tableSliding Table Extension Tables To install the extension tablesRip Fence and Scale To install the rip fencePage Main Blade To install the bladeScoring Blade To install the scoring bladeTo align the blades and riving knife Aligning BladesRiving Knife Alignment Page Sliding Table Parallelism To adjust the sliding table parallel with the main bladeCrosscut Fence To install the crosscut tableTo install the crosscut fence Crosscut TableTo align the fence scale with the blade Fence Scale AlignmentTest Run Power CordTo connect the saw to the power source Please follow these tips Every time you use your saw Operation Safety Operation TipsOperations Changing Blades Rip cutting with the sliding table Rip CuttingRip cutting using traditional table saw techniques Crosscutting Fence to Blade on Page 48 if necessary Crosscutting full size panelsTo perform a miter cut Miter CuttingG5562-SLIPIT1 Qt. Gel G5563-SLIPIT12 oz Spray AccessoriesG1955-OxiSolvBlade & Bit Cleaner G7895-Citrus DegreaserH6460-12 Tooth Scoring Blade Set H1300 H1298 G7984 H2347 H0736G7581-Superbar G7582-Master Plate H3308-SHOP FOX Push StickG3445-Precision Saw Tool H3771-Blade LocUnpainted Cast Iron MaintenanceCleaning ScheduleSliding table ways LubricationReplacing Belts ServiceAbout Service Page Blade Tilt To square the crosscut fence with the blade Squaring Crosscut Fence to BladeElectrical G0591 single phase magnetic switch Contactor Overload RelaySymptom Possible Cause Possible Solution TroubleshootingLoud repetitious noise coming Main Body PartsG0588/G0591 12 Sliding Table Saws PW01M Flat Washer 8MM PSB02M CAP Screw M6-1 X Saws Sliding Table G0588/G0591 12 Sliding Table Saws PN03M G0588/G0591 12 Sliding Table Saws PN01M HEX NUT M6-1 G0588/G0591 Rip Fence G0588/G0591 12 Sliding Table Saws Tilt Assembly G0588/G0591 12 Sliding Table Saws PK42M Motor AssemblyG0588/G0591 12 Sliding Table Saws Arbor Assembly G0588/G0591 12 Sliding Table Saws Warranty and Returns Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog