Bryant 123A manual Accessory Usage Guideline, Yes

ACCESSORY USAGE GUIDELINE

	REQUIRED FOR LOW---AMBI-	REQUIRED FOR LONG	REQUIRED FOR
		LINE	SEA COAST
ACCESSORY	ENT COOLING APPLICATIONS
		APPLICATIONS*	APPLICATIONS
	(Below 55°F/12.8_C)
		(Over 80 ft./24.38 m)	(Within 2 miles/3.22 km)
Ball Bearing Fan Motor	Yes{	No	No
Compressor Start Assist Capacitor and Relay	Yes	Yes	No
Crankcase Heater	Yes	Yes	No
Evaporator Freeze Thermostat	Yes	No	No
Hard Shut---Off TXV	Yes	Yes	Yes
Liquid Line Solenoid Valve	No	No	No
Motor Master→ Control or	Yes	No	No
Low---ambient Pressure Switch
Support Feet	Recommended	No	Recommended
Winter Start Control	Yes	No	No

*For tubing line sets between 80 and 200 ft. (24.38 and 60.96 m) and/or 20 ft. (6.09 m) vertical differential, refer to Residential Split---System Longline Application Guideline.

{Required for Low---Ambient Controller (full modulation feature) MotorMasterr Control.

ACCESSORY DESCRIPTION AND USAGE (LISTED ALPHABETICALLY)

123A

1. Ball-Bearing Fan Motor

A fan motor with ball bearings which permits speed reduction while maintaining bearing lubrication.

Usage Guideline:

Required on all units when using MotorMasterr

2. Compressor Start Assist - Capacitor and Relay

Start capacitor and relay gives a ”hard” boost to compressor motor at each start up.

Usage Guideline:

Required for single-phase scroll compressors in the following applications:

Long line Low-ambient cooling

Suggested for all compressors in areas with a history of low voltage problems.

3. Compressor Start Assist — PTC Type

Solid state electrical device which gives a ”soft” boost to the compressor at each start-up.

Usage Guideline:

Suggested in installations with marginal power supply.

4. Crankcase Heater

An electric resistance heater which mounts to the base of the compressor to keep the lubricant warm during off cycles. Improves compressor lubrication on restart and minimizes the chance of liquid slugging.

Usage Guideline:

Required in Low-ambient cooling applications. Required in long line applications.

Suggested in all commercial applications.

5. Cycle Protector

The cycle protector is designed to prevent compressor short cycling. This control provides an approximate 5-minute delay after power to the compressor has been interrupted for any reason, including power outage, protector control trip, thermostat jiggling, or normal cycling.

6. Evaporator Freeze Thermostat

An SPST temperature-actuated switch that stops unit operation when evaporator reaches freeze-up conditions.

Usage Guideline:

Required when Low-ambient kit has been added.

7. Low-Ambient Pressure Switch Kit

A long life pressure switch which is mounted to outdoor unit service valve. It is designed to cycle the outdoor fan motor in order to maintain head pressure within normal operating limits. The control will maintain working head pressure at low-ambient temperatures down to 0_F (-17.8_C) when properly installed.

Usage Guideline:

ALow-Ambient Pressure Switch must be used when cooling operation is at outdoor temperatures below 55_F (12.8_C) to a minimum of 0_F (-17.8_C).

Suggested for all commercial applications.

8. MotorMasterr Low-Ambient Controller

Afan-speed control device activated by a temperature sensor, designed to control condenser fan motor speed in response to the saturated, condensing temperature during operation in cooling mode only. For outdoor temperatures down to -20_F (-28.9_C), it maintains condensing temperature at 100_F ±10_F (37.8_C ± 6.5_C).

Usage Guideline:

A MotorMasterr Low Ambient Controller or Low-Ambient Pressure Switch must be used when cooling operation is used at outdoor temperatures below 55_F (12.8_C).

Suggested for all commercial applications.

5