Grizzly G9963, G9966, G3620 instruction manual Tooth Pitch, Blade Care, Blade Breakage

Page 25

Figure 18 shows the three main categories of tooth style.

RakerSkipHook

Figure 18. Raker, Skip and Hook blades.

RAKER — This style is considered to be the standard because the tooth size and shape are the same as the tooth gullet. The teeth on Raker blades are usually very numerous, have no angle, and produce cuts by scraping the material; these characteristics result in very smooth cuts, but at the same time do not cut fast and generate more heat while cutting.These blades also work well for cut- ting curves.

SKIP — This style is like a raker blade that is missing every other tooth. Because of the design, skip toothed blades have a much larger gullet than raker blades, and there- fore, cut faster and generate less heat. However, these blades also leave a rougher cut than raker blades. Great for resawing and ripping thin stock.

HOOK — The teeth on this style have a pos- itive angle (downward) which makes them dig into the material, and the gullets are usu- ally rounded for easier waste removal. These blades are excellent for the tough demands of resawing and ripping thick stock.

Tooth Pitch

Usually measured as T.P.I. (teeth per inch), tooth pitch determines the size of the teeth. More teeth

per inch (fine pitch) will cut slower, but smoother; while fewer teeth per inch (coarse pitch) will cut rougher, but faster. As a general rule, choose blades that will have at least three, but not more than twelve teeth in the material at all times. Use fine pitched blades on harder woods and coarse pitched blades on softer woods.

Blade Care

A bandsaw blade is a delicate piece of steel that is subjected to tremendous strain. You can obtain longer use from a bandsaw blade if you give it fair treatment and always use the appropriate feed rate for your operation.

Be sure to select blades with the proper width, style, and pitch for each application. The wrong choice of blades will often produce unnecessary heat which will shorten the life of your blade.

A clean blade will perform much better than a dirty blade. A dirty blade passes through the cut- ting material with much more resistance than a clean blade. This extra resistance will also cause unnecessary heat. Maintain your blades with a cutting blade lubricant like SLIPIT® (Model G5562/3 in the Grizzly Catalog).

Blade Breakage

Many conditions may cause a bandsaw blade to break. Blade breakage is unavoidable, in some cases, since it is the natural result of the peculiar stresses that bandsaw blades are subjected to. Blade breakage is also due to avoidable circum- stances. Avoidable breakage is most often the result of poor care or judgement on the part of the operator when mounting or adjusting the blade or support guides.

The most common causes of blade breakage are:

(1)faulty alignment or adjustment of the guides,

(2)forcing or twisting a wide blade around a curve of short radius, (3) feeding too fast, (4) tooth dull- ness or absence of sufficient set, (5) excessive tension, (6) top blade guide assembly set too high above the work piece, (7) using a blade with a lumpy or improperly finished braze or weld and

(8)running the bandsaw when not in use.

24" & 27" Resaw Bandsaws

-23-

Image 25
Contents Models G3619/G3620/G9963/G9966 Resaw BandsawsPage Table Of Contents Safety Instructions For Power Tools SafetyLength AMP Rating Additional Safety Instructions For Bandsaws Model G3619 Model G9963 Circuit RequirementsModel G3620/G9966 440V Operation Typical plug configuration for Three-phase operationGrounding Extension Cords Commentary General InformationUnpacking Piece Inventory Site Considerations Clean UpBeginning AssemblyFence Dust Port To install the dust portTo mount the fence Identification AdjustmentsBlade Guides Guide PostG9963/G9966 Blade Guides G3619/G3620 Blade GuidesG9963/G9966 Tracking G3619/G3620 TrackingTo center track your blade To track the bladeSupport Bearings To adjust the support bearings behind the bladeTo center the support bearings laterally Guide Blocks To center the blade guard Blade Guard Table StopMake sure the bandsaw is unplugged Table Tilt To tilt the table Disconnect power to the bandsawTest Run To adjust the tensionBlade Tension To adjust the fence so it is parallel with the blade Fence Adjustment Blade LeadBlade Selections OperationsBlade Length Blade WidthBlade Care Tooth PitchBlade Breakage Blade Changes To perform ripping operations Ripping Stacked CutsTo complete a stacked cut Resawing To resaw lumber, follow the procedure belowBelts MaintenanceMiscellaneous LubricationPage Page 24 & 27 Resaw Bandsaws 24 & 27 Resaw Bandsaws Closure Machine Data Sheet G3619/G3620 G3619/G3620 G3619/G3620 G3619/G3620 G3619/G3620 Frame Fence Rail Grizzly Model G9963/G9966 27 Bandsaw G9963/G9966 Arin g C o G9963/G9966 189 24 & 27 Resaw Bandsaws 8026 Hinge PIN Support Bearing Troubleshooting Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC