Grizzly G9963, G9966, G3620 instruction manual Safety Instructions For Power Tools

Page 4

SECTION 1: SAFETY

For Your Own Safety Read Instruction Manual Before Operating This Equipment

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

 

 

 

 

 

 

 

 

Indicates an imminently hazardous situation which, if not avoided,

 

 

 

 

 

 

 

 

WILL result in death or serious injury.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Indicates a potentially hazardous situation which, if not avoided,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COULD result in death or serious injury.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Indicates a potentially hazardous situation which, if not avoided,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MAY result in minor or moderate injury. It may also be used to alert

 

 

 

 

 

 

 

 

against unsafe practices.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTICE

 

This symbol is used to alert the user to useful information about

 

 

proper operation of the equipment.

 

 

 

 

 

 

 

 

 

Safety Instructions For Power Tools

1.KEEP GUARDS IN PLACE and in working order.

2.REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning on.

3.KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

4.DO NOT USE IN DANGEROUS ENVI- RONMENT. Do not use power tools in damp or wet locations, or where any flam- mable or noxious fumes may exist. Keep work area well lighted.

5.KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept at a safe distance from work area.

6.MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing starter keys.

7.DO NOT FORCE TOOL. It will do the job better and safer at the rate for which it was designed.

8.USE RIGHT TOOL. Do not force tool or attachment to do a job for which it was not designed.

-2-

24" & 27" Resaw Bandsaws

Image 4
Contents Resaw Bandsaws Models G3619/G3620/G9963/G9966Page Table Of Contents Safety Safety Instructions For Power ToolsLength AMP Rating Additional Safety Instructions For Bandsaws Circuit Requirements Model G3619 Model G9963Typical plug configuration for Three-phase operation Model G3620/G9966 440V OperationGrounding Extension Cords General Information CommentaryUnpacking Piece Inventory Clean Up Site ConsiderationsAssembly BeginningFence Dust Port To install the dust portTo mount the fence Adjustments IdentificationGuide Post Blade GuidesG9963/G9966 Blade Guides G3619/G3620 Blade GuidesG3619/G3620 Tracking G9963/G9966 TrackingTo center track your blade To track the bladeSupport Bearings To adjust the support bearings behind the bladeTo center the support bearings laterally Guide Blocks To center the blade guard Blade Guard Table StopMake sure the bandsaw is unplugged To tilt the table Disconnect power to the bandsaw Table TiltTest Run To adjust the tensionBlade Tension Fence Adjustment Blade Lead To adjust the fence so it is parallel with the bladeOperations Blade SelectionsBlade Length Blade WidthBlade Care Tooth PitchBlade Breakage Blade Changes To perform ripping operations Ripping Stacked CutsTo complete a stacked cut To resaw lumber, follow the procedure below ResawingMaintenance BeltsMiscellaneous LubricationPage Page 24 & 27 Resaw Bandsaws 24 & 27 Resaw Bandsaws Closure Machine Data Sheet G3619/G3620 G3619/G3620 G3619/G3620 G3619/G3620 G3619/G3620 Frame Fence Rail Grizzly Model G9963/G9966 27 Bandsaw G9963/G9966 Arin g C o G9963/G9966 189 24 & 27 Resaw Bandsaws 8026 Hinge PIN Support Bearing Troubleshooting Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WA