PERFORMANCE DATA | ASX140421[C/D]* - ASX140481C* |
MODEL: ASX140421[C*/D*] / CA*F4860*6B* W/.070 Orifice,
Conditions: 80°F IDB, 67°F IWB @ 1450 CFM
Outdoor | Total | Sensible | Latent | Total |
Temp. ° F. | Btuh | Btuh | Btuh | Watts |
75° | 42,116 | 29,985 | 12,131 | 2,950 |
80° | 41,614 | 30,004 | 11,610 | 3,040 |
85° | 41,113 | 30,015 | 11,098 | 3,130 |
90° | 40,611 | 30,127 | 10,485 | 3,205 |
95° | 40,110 | 30,227 | 9,883 | 3,280 |
100° | 39,107 | 30,029 | 9,078 | 3,350 |
|
|
|
|
|
105° | 38,105 | 29,803 | 8,301 | 3,420 |
110° | 36,701 | 28,826 | 7,875 | 3,475 |
|
|
|
|
|
115° | 35,297 | 27,839 | 7,458 | 3,530 |
| TVA Conditions @ 95° OD DB, 75° ID DB 63° ID WB | |||
95° | 37,200 | 30,132 | 7,068 | 3,160 |
ASX140481C* / CA*F4860*6D* W/.078 Orfice
Conditions: 80°F IDB, 67°F IWB @ 1550 CFM
Outdoor | Total | Sensible | Latent | Total | |
Temp. ° F. | Btuh | Btuh | Btuh | Watts | |
75° | 48,300 | 34,776 | 13,524 | 3,260 | |
80° | 47,750 | 34,858 | 12,893 | 3,365 | |
85° | 47,200 | 34,928 | 12,272 | 3,470 | |
90° | 46,600 | 34,950 | 11,650 | 3,560 | |
95° | 46,000 | 34,960 | 11,040 | 3,650 | |
100° | 44,850 | 34,759 | 10,091 | 3,725 | |
105° | 43,700 | 34,523 | 9,177 | 3,800 | |
110° | 42,100 | 33,470 | 8,631 | 3,865 | |
115° | 40,500 | 32,400 | 8,100 | 3,930 | |
TVA Conditions @ 95° OD DB, 75° ID DB, 63° ID WB | |||||
95° | 43,552 | 35,549 | 8,003 | 3,618 | |
PERFORMANCE TEST
All data based upon listed indoor dry bulb temperature. .00 inches external static pressure on coil of outdoor section. Indoor air cubic feet per minute (CFM) as listed in the Performance Data Sheets:
If conditions vary from this, results will change as follows:
1.As indoor dry bulb temperatures increase, a slight increase will occur in indoor air temperature drop (Delta T). Low and high side pressures and power will not change.
2.As indoor CFM decreases, a slight increase will occur in indoor temperature drop (Delta T). A slight decrease will occur in low and high side pressures and power.
A properly operating unit should be within plus or minus 2 degrees of the subcooling value shown in the installation instructions.
A properly operating unit should be within plus or minus 3 degrees of the typical (Delta T) value shown.
A properly operating unit should be within plus or minus 10 PSIG of the HI PR shown.
A properly operating unit should be within plus or minus 5 PSIG of the LO PR shown.
A properly operating unit should be within plus or minus 3 Amps of the typical value shown.
NOTE: Pressures are measures at the liquid and suction service valve ports.
39