Grizzly G0514X3, G0513X owner manual Blade Changes, To remove a blade, To replace a blade

Page 44

Blade Changes

Always disconnect power to the machine when changing blades. Failure to do this may result in serious personal injury.

All saw blades are dan- gerous and may cause personalinjury.Toreduce the risk of being injured, wear leather gloves when handling saw blades.

To remove a blade:

1.DISCONNECT BANDSAW FROM POWER!

2.Release the blade tension by turning the blade tension quick release lever to the left.

3.Remove the table insert and the table pin. Adjust the upper and lower guide bearings as far away as possible from the blade.

4.Open the upper and lower wheel covers, and with gloved hands, slide the blade off of both wheels.

5.Rotate the blade 90˚ and slide it through the slot in the table.

To replace a blade:

1.Slide the blade through the table slot, ensur- ing that the teeth are pointing down toward the table. Note: If the teeth will not point downward in any orientation, the blade is inside-out. Put on heavy gloves, remove the blade, and twist it right side-out.

2.Slip the blade through the guides, and mount it on the upper and lower wheels (Figure 52).

Figure 52. Placing blade on the wheels.

3.Tighten the blade tension lever.

4.Apply tension to the blade by turning the ten- sion control knob. Rotate the upper wheel slowly by hand as tension is applied to allow the blade to center itself on the wheel. Adjust tracking if needed.

5.Adjust tension as described Page 27.

6.Adjust the upper/lower guide bearings and the support bearings.

7.Close the wheel covers.

8.Replace the table insert and table pin, being sure not to use excessive force when insert- ing the table pin.

-42-

G0513X/G0514X/G0514X3 Extreme Series Bandsaw

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Extreme Series Bandsaw Page Table of Contents Accessories Maintenance Contact Info IntroductionForeword Machine Data Sheet Table Information G0514X Machine Data Sheet 26-3/4 G0514X3 Machine Data Sheet G0513X/G0514X/G0514X3 Extreme Series Bandsaw Identification Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Bandsaws Circuit Requirements OperationExtension Cords Phase ConverterGrounding SET UP Set Up SafetyItems Needed for Set Up UnpackingHardware and Tools Qty Crate Contents QtyInventory Hardware Recognition Chart Clean Up Site ConsiderationsTo move and place the bandsaw Moving & Placing Base UnitMounting To install the table Components and Hardware Needed QtyBlade Tracking To center track the bladeTo install the positive stop Positive StopTo connect a dust collection hose Dust CollectionTo set the positive stop Installing Fence To install the fenceTest Run Adjusting Support Bearings To adjust the upper support bearingsTensioning Blade To tension the bandsaw bladeTo adjust the lower support bearings Adjusting Blade Guide Bearings To adjust the upper and lower blade guidesAligning Table Aligning Fence To align the fence parallel with the miter slotOperation Safety Overview OperationsSTART/STOP Switch Guide Post G0513X START/STOP switchFine Tune Tracking Blade LeadTo correct blade lead To skew your fenceTo tilt the table Table TiltTo shift the table To make a 90˚ crosscut RippingCrosscuttingTo make a rip cut Resawing Resawing lumberCutting Curves Stacked Cuts To complete a stacked cutTo adjust the blade speed Blade SpeedBlade Information Blade LengthTooth Pitch Most common causes of blade breakage areTo replace a blade Blade ChangesTo remove a blade 1311⁄2 Carbon Steel Replacement Blades for the Model G0513X AccessoriesReplacement Blades H2347 H1300 H1298 G7984 H0736 H1302Maintenance Service TroubleshootingAdjust the feet on the bottom of the stand relocate Checking V-Belt Tensioning V-Belt To check the V-beltTools Needed Qty To tension the V-beltTo replace the V-belt Replacing V-BeltTools Needed Adjusting Tension Adjusting Wheel BrushTo adjust the tension lever To adjust the wheel brushWheel Alignment To check if your wheels are coplanarCoplanarity Gauge G0513X Electrical Components G0513X Wiring Diagram G0514X Electrical Components G0514X Wiring Diagram G0514X3 Electrical Components To Junction BoxG0514X3 Wiring Diagram G0513X G0513X Fence/Guide Parts G0513X Parts List DescriptionDescription G0513X Labels G0514X/G0514X3 Main Parts G0514X/G0514X3 Fence/Guide Parts G0514X/G0514X3 Labels G0514X/G0514X3 Parts List PSB30M CAP Screw M6-1 X PFS09M Flange Screw M5-.8 X Warranty and Returns Page Page
Related manuals
Manual 96 pages 51.1 Kb

G0514X3, G0514X, G0513X specifications

The Grizzly G0514X, G0513X, and G0514X3 are part of Grizzly Industrial's impressive lineup of band saws, engineered for woodworkers and metal fabricators seeking high-quality, precision cutting capabilities. Each model has distinct features, yet they share core characteristics that make them exceptional tools for professional and hobbyist use alike.

The Grizzly G0514X stands out with its powerful 2 HP motor, providing ample cutting power for thicker materials. It benefits from a 14-inch resaw capacity, making it capable of handling large workpieces effortlessly. A key feature of the G0514X is its cast-iron frame, which enhances stability and reduces vibration during operation. This model includes a 3-wheel design that allows for a greater cutting curve radius while maintaining a compact footprint. Additionally, it comes equipped with heavy-duty stainless steel guides and a dual tracking adjustment system, improving precision and blade longevity.

The G0513X, while slightly smaller in power with a 1 HP motor, does not compromise on performance. It also offers a generous 13-inch resaw capacity, making it an excellent choice for those who work with various wood thicknesses. The G0513X features an adjustable table that tilts, along with an easy-to-read scale for angle adjustments, providing flexibility for intricate cuts. Its sturdy construction ensures durability, while the variable speed control allows users to tailor the cutting speed based on material type, making it a versatile option for diverse woodworking projects.

The G0514X3 is a high-performance model that combines the best features of both its counterparts. Equipped with a robust 2 HP motor and a resaw capacity of 14 inches, this saw is designed for demanding applications. One of its standout technologies is the three-wheel design, which maximizes the throat depth while minimizing the space it occupies. The G0514X3 also includes premium ceramic guides, reducing friction and heat build-up during cutting, which extends blade life. A significant characteristic of the G0514X3 is its digital readout for blade tension, ensuring optimal operating conditions with minimal guesswork.

Overall, the Grizzly G0514X, G0513X, and G0514X3 represent the pinnacle of band saw technology, offering users powerful performance, precision, and advanced features tailored for a broad range of cutting applications. Whether for slicing veneer, resawing logs, or intricate metalwork, these band saws deliver the reliability and efficiency needed for any workshop.
Top Page Image Contents