Grizzly G0513X, G0514X3 owner manual Blade Tracking, To center track the blade

Page 24

Blade Tracking

Personal injury or death can occur if the machine starts while your hand is touching the bandsaw wheel during tracking adjustments. Disconnect power from the bandsaw before performing blade tracking adjustments.

The blade tracking is primarily affected by the tilt of the upper wheel, also known as "Center Tracking"; and the alignment of both wheels, also known as "Coplanar Tracking." (For Coplanar Tracking, see the Wheel Alignment instructions on Page 51.)

The wheels on this bandsaw were aligned at the factory, so Center Tracking is the only adjust- ment that needs to be performed when the saw is new.

To center track the blade:

1.DISCONNECT BANDSAW FROM POWER!

2.Make sure the upper and lower blade guides are adjusted away from the blade.

3.Engage the quick tension lever and turn the blade tension handwheel until the tension scale (Figure 16) reads between 4 and 6.

Blade Tension

Scale

Blade Tension

Handwheel

Figure 16. Blade tensioning controls.

-22-

4.Spin the upper wheel by hand at least three times and watch how the blade rides on the crown of the wheel. Refer to Figure 17 for an illustration of this concept.

—If the blade rides in the center of the upper wheel and is centered on the peak of the wheel crown, then the bandsaw is already tracked properly and no further adjustments are needed at this time.

—If the blade does not ride in the center of the upper wheel and is not centered on the peak of the wheel crown, then continue with the following steps.

The cast iron spokes may have sharp edges and the blade teeth may extend beyond the edge of the wheel, creating a laceration hazard. Be careful when turning the wheels by hand.

Blade Centered

on Peak of Crown

Blade

Centered on Wheel

CENTER TRACKING

Figure 17. Center tracking profiles.

G0513X/G0514X/G0514X3 Extreme Series Bandsaw

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Extreme Series Bandsaw Page Table of Contents Accessories Maintenance Introduction ForewordContact Info Machine Data Sheet Table Information G0514X Machine Data Sheet 26-3/4 G0514X3 Machine Data Sheet G0513X/G0514X/G0514X3 Extreme Series Bandsaw Identification Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Bandsaws Circuit Requirements OperationPhase Converter GroundingExtension Cords SET UP Set Up SafetyItems Needed for Set Up UnpackingCrate Contents Qty InventoryHardware and Tools Qty Hardware Recognition Chart Clean Up Site ConsiderationsMoving & Placing Base Unit MountingTo move and place the bandsaw To install the table Components and Hardware Needed QtyBlade Tracking To center track the bladeTo install the positive stop Positive StopDust Collection To set the positive stopTo connect a dust collection hose Installing Fence To install the fenceTest Run Adjusting Support Bearings To adjust the upper support bearingsTensioning Blade To tension the bandsaw bladeTo adjust the lower support bearings Adjusting Blade Guide Bearings To adjust the upper and lower blade guidesAligning Table Aligning Fence To align the fence parallel with the miter slotOperation Safety Overview OperationsSTART/STOP Switch Guide Post G0513X START/STOP switchFine Tune Tracking Blade LeadTo correct blade lead To skew your fenceTable Tilt To shift the tableTo tilt the table RippingCrosscutting To make a rip cutTo make a 90˚ crosscut Resawing Resawing lumberCutting Curves Stacked Cuts To complete a stacked cutTo adjust the blade speed Blade SpeedBlade Information Blade LengthTooth Pitch Most common causes of blade breakage areBlade Changes To remove a bladeTo replace a blade Accessories Replacement Blades1311⁄2 Carbon Steel Replacement Blades for the Model G0513X H2347 H1300 H1298 G7984 H0736 H1302Maintenance Service TroubleshootingAdjust the feet on the bottom of the stand relocate Checking V-Belt Tensioning V-Belt To check the V-beltTools Needed Qty To tension the V-beltReplacing V-Belt Tools NeededTo replace the V-belt Adjusting Tension Adjusting Wheel BrushTo adjust the tension lever To adjust the wheel brushWheel Alignment To check if your wheels are coplanarCoplanarity Gauge G0513X Electrical Components G0513X Wiring Diagram G0514X Electrical Components G0514X Wiring Diagram G0514X3 Electrical Components To Junction BoxG0514X3 Wiring Diagram G0513X G0513X Fence/Guide Parts G0513X Parts List DescriptionDescription G0513X Labels G0514X/G0514X3 Main Parts G0514X/G0514X3 Fence/Guide Parts G0514X/G0514X3 Labels G0514X/G0514X3 Parts List PSB30M CAP Screw M6-1 X PFS09M Flange Screw M5-.8 X Warranty and Returns Page Page
Related manuals
Manual 96 pages 51.1 Kb

G0514X3, G0514X, G0513X specifications

The Grizzly G0514X, G0513X, and G0514X3 are part of Grizzly Industrial's impressive lineup of band saws, engineered for woodworkers and metal fabricators seeking high-quality, precision cutting capabilities. Each model has distinct features, yet they share core characteristics that make them exceptional tools for professional and hobbyist use alike.

The Grizzly G0514X stands out with its powerful 2 HP motor, providing ample cutting power for thicker materials. It benefits from a 14-inch resaw capacity, making it capable of handling large workpieces effortlessly. A key feature of the G0514X is its cast-iron frame, which enhances stability and reduces vibration during operation. This model includes a 3-wheel design that allows for a greater cutting curve radius while maintaining a compact footprint. Additionally, it comes equipped with heavy-duty stainless steel guides and a dual tracking adjustment system, improving precision and blade longevity.

The G0513X, while slightly smaller in power with a 1 HP motor, does not compromise on performance. It also offers a generous 13-inch resaw capacity, making it an excellent choice for those who work with various wood thicknesses. The G0513X features an adjustable table that tilts, along with an easy-to-read scale for angle adjustments, providing flexibility for intricate cuts. Its sturdy construction ensures durability, while the variable speed control allows users to tailor the cutting speed based on material type, making it a versatile option for diverse woodworking projects.

The G0514X3 is a high-performance model that combines the best features of both its counterparts. Equipped with a robust 2 HP motor and a resaw capacity of 14 inches, this saw is designed for demanding applications. One of its standout technologies is the three-wheel design, which maximizes the throat depth while minimizing the space it occupies. The G0514X3 also includes premium ceramic guides, reducing friction and heat build-up during cutting, which extends blade life. A significant characteristic of the G0514X3 is its digital readout for blade tension, ensuring optimal operating conditions with minimal guesswork.

Overall, the Grizzly G0514X, G0513X, and G0514X3 represent the pinnacle of band saw technology, offering users powerful performance, precision, and advanced features tailored for a broad range of cutting applications. Whether for slicing veneer, resawing logs, or intricate metalwork, these band saws deliver the reliability and efficiency needed for any workshop.
Top Page Image Contents