Harbor Freight Tools 68023 Functional Description, Specifications, Unpacking

Page 7

FUNCTIONAL DESCRIPTION

Functional Description

Specifications

to the Assembly Diagram near the end of this manual.

Unpacking

Maximum Air

 

120 PSI

 

 

 

When unpacking, make sure that the

Pressure

 

 

 

 

 

 

 

 

 

 

 

 

 

item is intact and undamaged. If any parts

Air Consumption

 

1 CFM @ 90 PSI

 

 

 

 

 

 

 

are missing or broken, please call Harbor

Air Inlet

 

1/4” -18 NPT

 

 

 

 

 

 

 

Freight Tools at 1‑800‑444‑3353 as soon as

Fastener Sizes

 

1-1/4”, 1-1/2”, 1-3/4”, 2”, 2-1/2”

 

 

 

possible.

Magazine Capacity

 

100

 

 

 

 

 

 

 

• This air tool may be shipped with a

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

protective plug covering the air inlet.

Components and Controls

Remove this plug before set up.

 

 

 

 

 

 

 

 

 

 

 

 

 

Air Deflector (2)

 

 

 

 

 

 

 

 

 

 

 

Air Inlet

 

Air Supply

 

 

 

 

 

 

 

 

 

 

 

 

 

Plug (83)

 

 

TO PREVENT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXPLOSION:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Use only clean, dry, regulated,

 

 

 

 

 

 

 

 

 

compressed air to power this

 

 

 

 

 

 

 

 

 

tool. Do not use oxygen, carbon

 

 

 

 

 

Trigger

 

 

 

dioxide, combustible gases, or

 

 

 

 

 

 

Latch (73)

any other bottled gas as a power

 

 

 

 

(38)

 

source for this tool.

 

 

 

 

 

 

 

 

 

Safety (51)

Safety Nosepiece - Also called the workpiece

contact, the Safety Nosepiece helps prevent the tool from firing unless it is pressed against an object.

Initial ToolINITIALSetup/AssemblyASSEMBLY

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

Note: For additional information regarding the parts listed in the following pages, refer

1.Connect a regulator valve, an in-line shut off valve and 1/4” NPT air hose (all sold separately) to the Quick Coupler. Use thread tape on all threaded connections. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working. An in-line shutoff ball valve is an important safety device because it controls air supply even if air hose is ruptured. The shutoff valve should be a ball valve because it can be closed quickly. See pages 8 and 9 for Air Tool Setup procedures.

Note: If an automatic oiler system is not used, add a few drops of Pneumatic Tool Oil into the airline connection before operation. Add a few more drops after each hour of continual use.

SKU 68023

For technical questions, please call 1-800-444-3353.

Page 7

Image 7
Contents Gauge AIR Finish Nailer For technical questions, please call Safety Alert Symbol and Signal WordsSymbol Property or statement Save this ManualGeneral Personal safetyWork area Tool use and care ServiceAir source Save These Instructions Vibration Precautions Components and Controls SpecificationsFunctional Description UnpackingSKU A EAir Tool Spray Gun Stationary SKU 68023 For technicalQuestions, please call Injury from Accidental Operation Operating Instructions Work Piece and Work Area Set UpFull Sequential Safety Trip Mechanism Definition Full Sequential Safety Trip Mechanism Testing ProcedureGeneral Operating Instructions Loading the ToolDo not exceed 120 Max. PSI To Prevent Serious Injury User-Maintenance InstructionsUSER-INSTRUCTIONS Clearing JamsFor technical questions, please call Problem Possible Causes Likely Solutions TroubleshootingQty For technical questions, please call Parts ListPart Description Qty Part Description444-3353 Assembly DiagramLimited 1-Year Warranty