Harbor Freight Tools 68068 owner manual Loading the Tool, General Operating Instructions

Page 11

Loading the Tool

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION, BEFORE LOADING:

•Wear ANSI-approved safety goggles with side shields.

Other people in the work area must also wear ANSI-approved impact safety goggles with side shields.

•Release the trigger.

•Detach the air supply.

•Attempt to fire the Tool into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any fasteners.

1.Pull Feeder Shoe all the way to the rear of Magazine. 3. When loading nails, make sure the

2. Orient a strip of nails with the tips down and

nails are correct angle for nailer.

 

drop the strip of nails into Magazine.

4. Allow Feeder Shoe to slide forward

 

against strip of nails.

General Operating Instructions

SAFETY

1.Before each use, test the tool as directed in the prior section.

2.If an automatic oiler is not used, add a few drops of Pneumatic Tool Oil to the airline connection before use. Add a few drops more after each hour of continual use.

3.Attach the Nailer to the air supply at the air inlet. Start your compressor and check the pressure making sure it is set at the recommended 70-120 PSI and not to go over the maximum 120 PSI.

4.Adjust Exhaust Cover to direct as desired.

5.To fire a nail, place the nose of the Nailer on the workpiece. The Nailer should not fire if the Safety is not depressed. Once the Safety is depressed, gently and briefly squeeze the Trigger once to fire one nail. Release the Trigger. Do not fire repeatedly; nails could bounce off on one another, damaging the workpiece or causing personal injury.

6.If nails are not being driven flush, turn the Depth Knob to the left.

7.Move the Nailer to another spot on the workpiece and squeeze the Trigger again to fire another nail. Continue firing nails as needed.

8.If the tool requires more force to accomplish the task, verify that the tool receives sufficient, unobstructed airflow (CFM) and increase the pressure (PSI) output of the regulator up to the maximum air pressure rating of this tool.

CAUTION! TO PREVENT INJURY FROM TOOL OR ACCESSORY FAILURE:

Do not exceed the tool’s maximum air pressure rating.

If the tool still does not have sufficient force at maximum pressure and sufficient airflow, then a larger tool may be required.

9.After use, to prevent accidents:

a.Release the trigger.

b.Detach the air supply.

c.Attempt to fire the Tool into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any fasteners.

d.Release the trigger again.

e.Clean external surfaces with clean, dry cloth.

f.Store indoors out of children’s reach.

SETUP

OPERATION

MAINTENANCE

Item 68028

For technical questions, please call 1-800-444-3353.

Page 11

68068

 

 

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Framing nailer 28 angle Angle Table of Contents Work area Personal safetyGeneral Air source ServiceTool use and care Specific Safety Instructions Functional Description Vibration PrecautionsSpecifications Components and ControlsAir Supply Initial Tool Set Up/AssemblyDescription Function L M F Operating Instructions Work Piece and Work Area Set UpSingle Sequential Safety Trip Mechanism Definition Single Sequential Safety Trip Mechanism Testing ProcedureGeneral Operating Instructions Loading the ToolClearing Jams User-Maintenance InstructionsProblem Possible Causes Likely Solutions TroubleshootingParts List and Diagram Parts ListAssembly Diagram Limited 90 Day Warranty

68068 specifications

Harbor Freight Tools 68068 is a powerful and versatile tool that caters to both DIY enthusiasts and professional tradespeople alike. Known for its affordability and robust design, this tool has gained a reputation for reliability and efficiency.

One of the standout features of the Harbor Freight Tools 68068 is its high output. Equipped with a powerful motor, it delivers consistent performance across various applications. Whether you’re cutting, grinding, or polishing, this tool is designed to handle demanding tasks with ease. Its ability to reach high speeds allows users to complete jobs quickly and effectively, making it a highly sought-after addition to any workshop.

The 68068 also incorporates advanced technology to enhance user experience and safety. It features a user-friendly interface with easily accessible controls, allowing for seamless operation. Additionally, it is designed with an ergonomic grip that ensures comfortable handling, reducing user fatigue during prolonged use. This thoughtful design is crucial for professionals who rely on this tool for extensive periods.

Another key characteristic of the Harbor Freight Tools 68068 is its durability. Constructed from high-quality materials, this tool is built to withstand the rigors of daily use. Its rugged exterior not only protects the internal components but also ensures longevity, making it a cost-effective choice for users who demand reliability over time.

Versatility is another significant advantage of the 68068. It comes with an array of attachments and accessories that allow users to switch between different tasks effortlessly. From sanding and buffing to cutting and drilling, the capability to adapt to various applications makes it a must-have tool for any toolbox.

Moreover, the Harbor Freight Tools 68068 comes with a comprehensive warranty, reflecting the manufacturer’s confidence in its quality and performance. This assurance provides peace of mind for buyers, knowing that their investment is protected against defects and issues.

In conclusion, the Harbor Freight Tools 68068 is a feature-packed tool that offers power, durability, and versatility. With its user-friendly design, advanced technology, and array of capabilities, it serves as an indispensable asset for both hobbyists and professionals. Whether tackling home improvement projects or professional jobs, the 68068 ensures that users have the right tool to get the job done efficiently and effectively.
Top Page Image Contents