Harbor Freight Tools 68068 owner manual Clearing Jams, User-Maintenance Instructions

Page 12

SAFETY

SETUP

User-Maintenance Instructions

Procedures not specifically explained in this manual must be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION,

BEFORE ANY MAINTENANCE OR REPAIRS ARE DONE (including clearing jams):

•Wear ANSI-approved safety goggles with side shields.

Other people in the work area must also wear ANSI-approved impact safety goggles with side shields.

•Release the trigger.

•Detach the air supply.

•Attempt to fire the Tool into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any fasteners.

•Empty the magazine and leave it open during service.

The Magazine is spring‑loaded and may cause parts or a fastener to fly out of the Tool.

TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment.

If abnormal noise, vibration, or leaking air is detected, have the problem corrected before further use.

TO PREVENT EXPLOSION: Lubricate only with specified lubricants. Lubricate the air inlet using only pneumatic tool oil. Lubricate the internal mechanism using only white lithium grease.

Other lubricants may damage the mechanism and may be highly flammable, causing an explosion.

Note: These procedures are in addition to the regular checks and maintenance explained as part of the regular operation of the air-operated tool.

1.BEFORE EACH USE, inspect the general condition of the tool. Check for:

•loose hardware or housing,

•misalignment or binding of moving parts,

•cracked or broken parts, and

•any other condition that may affect its safe operation.

2.Daily - Air Supply Maintenance:

Every day, perform maintenance on the air supply according to the component manufacturers' instructions. Maintain the lubricator's oil level. Drain the moisture filter regularly.

Performing routine maintenance on the air supply will allow the tool to operate more safely and will also reduce wear on the tool.

OPERATION

Clearing Jams

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION,

BEFORE ANY MAINTENANCE OR REPAIRS ARE DONE (including clearing jams):

•Wear ANSI-approved safety goggles with side shields.

Other people in the work area must also wear ANSI-approved impact safety goggles with side shields.

•Release the trigger.

•Detach the air supply.

•Attempt to fire the Tool into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any fasteners.

•Empty the magazine and leave it open during service.

The Magazine is spring‑loaded and may cause parts or a fastener to fly out of the Tool.

MAINTENANCE

1.If a fastener is jammed in the discharge area, remove it with pliers.

2.If a fastener is jammed in the magazine, pull the Pusher all the way back to the engaged position. Use a screwdriver to release the jammed fastener by probing the openings in the magazine.

3.Pull out the jammed fastener and the remainder of the fastener strip from the magazine.

Dispose of the remaining fastener strip;

it is likely bent or damaged and may cause repeated jamming or damage to the tool if reused.

4.If the jam cannot be cleared using the method above, have the tool serviced by a qualified technician.

Page 12

For technical questions, please call 1-800-444-3353.

Item 68028

 

 

68068

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Framing nailer 28 angle Angle Table of Contents Personal safety GeneralWork area Service Tool use and careAir source Specific Safety Instructions Vibration Precautions SpecificationsComponents and Controls Functional DescriptionInitial Tool Set Up/Assembly Air SupplyDescription Function L M F Work Piece and Work Area Set Up Single Sequential Safety Trip Mechanism DefinitionSingle Sequential Safety Trip Mechanism Testing Procedure Operating InstructionsLoading the Tool General Operating InstructionsUser-Maintenance Instructions Clearing JamsTroubleshooting Problem Possible Causes Likely SolutionsParts List Parts List and DiagramAssembly Diagram Limited 90 Day Warranty

68068 specifications

Harbor Freight Tools 68068 is a powerful and versatile tool that caters to both DIY enthusiasts and professional tradespeople alike. Known for its affordability and robust design, this tool has gained a reputation for reliability and efficiency.

One of the standout features of the Harbor Freight Tools 68068 is its high output. Equipped with a powerful motor, it delivers consistent performance across various applications. Whether you’re cutting, grinding, or polishing, this tool is designed to handle demanding tasks with ease. Its ability to reach high speeds allows users to complete jobs quickly and effectively, making it a highly sought-after addition to any workshop.

The 68068 also incorporates advanced technology to enhance user experience and safety. It features a user-friendly interface with easily accessible controls, allowing for seamless operation. Additionally, it is designed with an ergonomic grip that ensures comfortable handling, reducing user fatigue during prolonged use. This thoughtful design is crucial for professionals who rely on this tool for extensive periods.

Another key characteristic of the Harbor Freight Tools 68068 is its durability. Constructed from high-quality materials, this tool is built to withstand the rigors of daily use. Its rugged exterior not only protects the internal components but also ensures longevity, making it a cost-effective choice for users who demand reliability over time.

Versatility is another significant advantage of the 68068. It comes with an array of attachments and accessories that allow users to switch between different tasks effortlessly. From sanding and buffing to cutting and drilling, the capability to adapt to various applications makes it a must-have tool for any toolbox.

Moreover, the Harbor Freight Tools 68068 comes with a comprehensive warranty, reflecting the manufacturer’s confidence in its quality and performance. This assurance provides peace of mind for buyers, knowing that their investment is protected against defects and issues.

In conclusion, the Harbor Freight Tools 68068 is a feature-packed tool that offers power, durability, and versatility. With its user-friendly design, advanced technology, and array of capabilities, it serves as an indispensable asset for both hobbyists and professionals. Whether tackling home improvement projects or professional jobs, the 68068 ensures that users have the right tool to get the job done efficiently and effectively.
Top Page Image Contents