Global Machinery Company LSM210A instruction manual Cross-cutting With slide action, Bevel cut

Page 16

12. Release the switch trigger

 

k

(24) and allow the saw

 

blade to stop rotating before

 

raising the blade out of the

 

workpiece. Wait until the

 

blade stops before removing

 

the workpiece (Fig. k).

 

Cross-cutting

 

 

(with slide action)

 

 

 

l

When cutting wide workpieces,

 

first unscrew the slide lock (29).

 

1.Pull on the release knob (6), raise the saw arm (5) to its highest position and slide it towards you (Fig. l).

2.Hold the handle firmly and

squeeze the switch trigger (24). Allow the blade to reach maximum speed.

3.Press the release latch (35) and slowly lower the blade into the workpiece and slide it away from you at the same time until the workpiece is cut.

4.Release the switch trigger (24) and allow the saw blade to stop rotating before raising the blade out of the workpiece. Wait until the blade stops before removing the workpiece.

Bevel cut

 

A bevel cut is made by cutting

 

m

across the grain of the workpiece

 

with the blade angled to the fence

 

and mitre table. The mitre table

 

is set at the zero degree position

 

and the blade set at an angle

 

between 0º and 45º (Fig. m).

 

Use the slide action when cutting

 

wide workpieces.

 

1.Pull on the release knob (6) and lift the saw arm to its full height.

2.Loosen the mitre lock (25).

3.Rotate the mitre table (21) until the pointer aligns with zero on the mitre scale (22).

4.Retighten the mitre lock (25).

WARNING. Be sure to tighten the mitre lock before making a cut. Failure to do so could result in the table moving during the cut, causing serious personal injury.

5.Loosen the bevel lock (16) and move the saw arm (5) to the left to the desired bevel angle (between 0º and 45º). Tighten the bevel lock (16).

6.Place the workpiece flat on the table with one edge securely against the fence (18). If the board is warped, place the convex side against the fence. If the concave side is placed against the fence, the board could break and jam the blade.

7.When cutting long pieces of timber, support the opposite end of the timber with the side bars (36), a roller stand or a work surface that is level with the saw table.

8.Use the clamp assembly (10) to secure the workpiece wherever possible.

9.It is possible to remove the clamp assembly (10) by loosening the clamp assembly lock (11) and moving it to the other side of the table. Make sure the clamp assembly lock is tight before using the clamp.

10.Before turning on the saw, perform a dry run of the cutting operation to check that there are no problems.

11.Hold the operating handle (7) firmly and squeeze

the switch trigger (24). Allow the blade to reach maximum speed.

12.Press the release latch (35) and slowly lower the blade into and through the workpiece.

13.Release the switch trigger (24) and allow the saw blade to stop rotating before raising the blade out of the workpiece. Wait until the blade stops before removing the workpiece.

16

Image 16
Contents Slide Compound Mitre SAW Contents Description of symbols SpecificationsIntroduction Environmental protectionSafety rules for laser lights General safety instructionsPage Additional safety rules for mitre saws Wear goggles Wear earmuffs Wear a breathing mask Accessories Adjustment screw Know your productUnpacking TransportationBench mounting Release knobClamp assembly Mitre table lockBevel lock Spindle lock buttonTrench depth adjustment Setting the table square with the bladeAttaching the side bars Turning on and offSetting the fence square with the table Changing a blade Cross-cutting without slide action Cross-cutting With slide action Bevel cutAdjusting the laser lines Compound mitre cutUsing the laser line generator Maintenance Power cord maintenanceCleaning General inspectionPage GMC customer assist