Grizzly H2912/H2913 instruction manual Troubleshooting, Problem Cause Action

Page 15

TROUBLESHOOTING

PROBLEM

 

CAUSE

 

ACTION

 

Air leaking at trigger valve

1. O-rings in trigger valve

1.

O-rings must be replaced

area.

 

housing are damaged.

 

& operation of

safety

 

 

 

 

yoke must be checked.

 

 

 

 

 

Air leaking between hous-

1. Loose screws in housing.

1.

Tighten screws.

 

ing and hose.

2. Damaged O-ring.

2.

Replace O-ring.

 

 

3.

Loose air fitting.

3.

Tighten air fitting.

 

 

 

 

 

Air leaking between hous-

1. Damaged seal.

1.

Replace damaged seals.

ing and cap assembly.

 

 

 

 

 

 

 

 

 

 

Tool skips staples/nails

1. Air leaks.

1.

Tighten screws and fit-

while discharging.

 

 

 

tings.

 

 

 

2.

Dirt in nose.

2.

Clean nose.

 

 

3.

Dirt or damage prevents sta-

3.

Clean

magazine

and

 

 

ples/nails from moving freely

 

inspect/repair damage.

 

 

in magazine.

 

 

 

 

 

4.

Inadequate air flow to tool.

4.

Check fitting, hose, com-

 

 

 

 

pressor & air pressure.

 

5.

Worn O-ring on piston or

5.

Replace piston O-ring.

 

 

lack of lubrication.

 

Lubricate.

 

 

6.

Damaged O-rings on trigger

6.

Replace trigger valve O-

 

 

valve.

 

rings.

 

 

 

7.

Worn bumper.

7.

Replace bumper.

 

 

8.

Cap seal leaking.

8.

Replace cap seal.

 

 

 

 

 

 

Tool runs slowly or has a

1. Tool is not sufficiently lubri-

1.

Lubricate tool.

 

loss of power.

 

cated.

 

 

 

 

 

2.

Broken spring in cap assem-

2.

Replace spring.

 

 

 

bly.

 

 

 

 

 

3.

Exhaust port in cap is

3.

Clean or replace dam-

 

 

blocked.

 

aged internal parts.

 

 

 

 

Fasteners frequently jam

1. Staples/nails are the wrong

1.

Use correct staples/nails.

the tool.

 

size.

2.

Use

undamaged

sta-

 

2.

Staples/nails are bent.

 

ples/nails.

 

 

3.

Magazine or nose screws

3.

Tighten magazine and

 

 

are loose.

 

nose screws.

 

 

4.

Driver or driver guide are

4.

Replace worn or dam-

 

 

worn or damaged.

 

aged parts.

 

 

 

 

 

 

Tool does not fire.

1. Staple/nail is jammed in

1.

Clear

tool magazine or

 

 

magazine or discharge

 

discharge area.

 

 

 

area.

 

 

 

 

 

2. Piston shaft is damaged.

2.

Replace piston shaft.

 

3. Air pressure too low.

3.

Check/increase air pres-

 

 

 

 

sure.

 

 

H2912/H2913 2-IN-1 NAILER/STAPLER

-14-

Image 15
Contents Model H2912/H2913 IN-1 NAILER/STAPLER KITBefore Operating This Equipment SafetyAMP Length Rating Nailer/Stapler Safety Commentary IntroductionCompressed Air System Safety Yoke MechanismOperating The Nailer/Stapler Depth AdjustmentOperation Loading The Nailer/StaplerDisconnect the nailer/stapler from the air supply Clearing Jammed Staples/NailsOiling The Nailer/Stapler Cleaning The Nailer/StaplerReplacing Pistons/O-Rings H2912 Part Breakdown 07 PH2912007 Piston Stopper H2913 Part Breakdown 07 PH2913007 Piston Stopper Problem Cause Action TroubleshootingWarranty and Returns Warranty Card Place Stamp Here