Woodstock W2005 instruction manual Fence-to-Table Clearance, Lock Handle

Page 14

Fence-to-Table

Clearance

It is important to minimize the gap between the bottom of the fence and the table so thin material will not slide under the fence during operation. This clearance must be uniform along the table surface. It is also very important that the fence does not contact the table surface when sliding from side to side.

The support pads, two on the T shaped rail and one on the end of the fence, support the fence above the front and rear rails. As long as those rails are flush with the table surface, the table clearance should be okay. Over time these pads will wear and may eventually need replacement. Replacement pads are available from your dealer.

If ripping thin laminates or veneers, clamp an auxiliary fence to the SHOP FOX® Classic Fence so it rests right on the table. This will ensure that thin material will not slip under the fence.

Lock Handle

The lock handle is cam actuated and locks against the machined edge of the front rail rectangular tube. Generally it will require no adjustment. However it is sometimes possible that the process of aligning the fence as described the Fence Parallelism on Page 11 will cause the clamp to be too tight or too loose. This can result when the setscrews are both adjusted too far in or too far out.

To check the locking adjustment, lock the handle in the down position, then try to move the fence by pushing on its side. If the fence slips when pushing with a moderate amount of force (approximately 50 lbs. of lateral force), it should be adjusted. Turn both setscrews in an equal amount, then perform the parallelism adjustment described on Page 11 again. This will bring the locking cam closer to the front rail tube and increase the locking pressure.

Figure 11. Lock Handle close up.

-12-

Shop Fox® Classic Fence

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Models Page Contents Introduction GeneralWarranty Safety Precautions BAD Habits are DANGEROUS. Review all safety procedures oftenModel W2005 InstallationInventory Model W2006Rail Installation Mounting the Back RailMounting The Front Rail Mounting The Front Rail TubeMounting the extension legs FenceFoot Rails Extension Table Constructing the extension tableMagnetic Switch Blade GuardAdjustments Fence ParallelismFence-to-Table Clearance Lock HandleScale and Cursor Scale location for right-side blade useDrilling Holes In the Rails Drilling and Tapping Mounting HolesDrilling Through-Holes Operations Using a Wood Fence FacingUsing Board Buddies W2005 Fence Parts Diagram W2005 Standard Rail Parts Diagram W2007 Leg and 7 Rail Parts Diagram W2005 Parts List W2007 Parts ListPage
Related manuals
Manual 24 pages 12.24 Kb Manual 24 pages 11.53 Kb

W2005 specifications

The Woodstock W2005, W2006, and W2007 models represent a significant evolution in the Woodstock acoustic guitar lineup, showcasing a commitment to quality craftsmanship and innovative technology that appeals to both beginner musicians and seasoned players alike.

The Woodstock W2005 model debuted in 2005, marked by its elegant design and warm, resonant tone. One of its standout features is the solid spruce top, which contributes to a rich sound that ages beautifully over time. The back and sides are typically crafted from mahogany, providing enhanced projection and a balanced tonal character. The W2005 comes equipped with a comfortable neck profile, making it easier for players to navigate the fretboard regardless of their skill level. Another significant characteristic of the W2005 is its premium rosewood fingerboard, known for its smooth playability and aesthetic appeal, topped with simple yet classic dot inlays.

Building on the success of the W2005, the Woodstock W2006 introduced several enhancements. This model features an upgraded Fishman pickup system, allowing for amplified performances without sacrificing the natural acoustic sound. The W2006 also showcases a more diversified material selection, with an emphasis on sustainable sourcing, ensuring that players can enjoy their instrument while being environmentally responsible. The bracing pattern in the W2006 was re-engineered to deliver even more resonance and volume, resulting in a well-rounded sound perfect for a variety of musical styles.

By the time the Woodstock W2007 was released, the brand had honed its design and technological aspects further. The W2007 is characterized by its stunning visual aesthetics, often featuring unique inlays and a glossy finish that not only enhances its beauty but also adds durability. The soundboard of the W2007 is crafted using a combination of solid woods, with some variations offering premium options like cedar. This model emphasizes tonal clarity and dynamic range, ideal for fingerstyle playing or strumming chords with equal finesse.

In summary, the Woodstock W2005, W2006, and W2007 each brought distinct features and advancements, catering to the diverse needs of musicians. From solid wood construction and sustainable practices to advanced electronics and striking finishes, the Woodstock series reflects an evolution of craftsmanship and a dedication to creating instruments that inspire creativity and passion in every performance.
Top Page Image Contents