Woodstock W2005 instruction manual Mounting The Front Rail Tube

Page 9

Mounting The Front Rail

1.Align the side of the front rail with two rectangular cutouts against the edge of the table.

2.Set the top edge of the front rail so it is flush with the table top and the cutouts are in line with the miter slots. If your saw table has a beveled front edge, then align the top of the rail with the bottom edge of the bevel. See Figure 3.

Bottom Edge

of Bevel

Figure 3. Attaching the front rail bracket.

3.Attach the rail using the mounting hardware from the old rail or two 3⁄8"-16 x 1" or M10-1.5 X 25 hex head bolts and washers. Secure as shown in Figure 2.

Mounting The Front Rail Tube

1.Orient the machined flat edge of the tube so it faces the table edge.

2.Thread four 1⁄4-20 X 3⁄4" hex bolts and 1⁄4" washers through the rail and into the threaded holes in the bottom of the tube.

3.If your table has a beveled front edge, it may be necessary to install spacers or shims between the rail and the rectangular tube as shown in Figure 4. The spacers should equal approximately the height of the bevel (3⁄8" on most saws). Four to six washers installed with each of the four attachment screws should raise the height of the tube enough to assure clearance of the fence above the table surface.

4.Mount the fence on the rails and check the clearance between the bottom edge of the HDPE facing and the table top.

5.Add or remove shims from the tube to rail mounting until a clearance of at least 1⁄16" is achieved. Note—This clearance should never exceed 1⁄8", as this can allow material to get under the fence during certain types of sawing operations.

Note: Do not install the scale at this time.

 

Figure 4. Shimming the front tube.

Shop Fox® Classic Fence

-7-

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Models Page Contents General IntroductionWarranty BAD Habits are DANGEROUS. Review all safety procedures often Safety PrecautionsInventory InstallationModel W2005 Model W2006Mounting the Back Rail Rail InstallationMounting The Front Rail Tube Mounting The Front RailFence Foot RailsMounting the extension legs Constructing the extension table Extension TableBlade Guard Magnetic SwitchFence Parallelism AdjustmentsLock Handle Fence-to-Table ClearanceScale location for right-side blade use Scale and CursorDrilling and Tapping Mounting Holes Drilling Through-HolesDrilling Holes In the Rails Using a Wood Fence Facing Using Board BuddiesOperations W2005 Fence Parts Diagram W2005 Standard Rail Parts Diagram W2007 Leg and 7 Rail Parts Diagram W2007 Parts List W2005 Parts ListPage
Related manuals
Manual 24 pages 12.24 Kb Manual 24 pages 11.53 Kb

W2005 specifications

The Woodstock W2005, W2006, and W2007 models represent a significant evolution in the Woodstock acoustic guitar lineup, showcasing a commitment to quality craftsmanship and innovative technology that appeals to both beginner musicians and seasoned players alike.

The Woodstock W2005 model debuted in 2005, marked by its elegant design and warm, resonant tone. One of its standout features is the solid spruce top, which contributes to a rich sound that ages beautifully over time. The back and sides are typically crafted from mahogany, providing enhanced projection and a balanced tonal character. The W2005 comes equipped with a comfortable neck profile, making it easier for players to navigate the fretboard regardless of their skill level. Another significant characteristic of the W2005 is its premium rosewood fingerboard, known for its smooth playability and aesthetic appeal, topped with simple yet classic dot inlays.

Building on the success of the W2005, the Woodstock W2006 introduced several enhancements. This model features an upgraded Fishman pickup system, allowing for amplified performances without sacrificing the natural acoustic sound. The W2006 also showcases a more diversified material selection, with an emphasis on sustainable sourcing, ensuring that players can enjoy their instrument while being environmentally responsible. The bracing pattern in the W2006 was re-engineered to deliver even more resonance and volume, resulting in a well-rounded sound perfect for a variety of musical styles.

By the time the Woodstock W2007 was released, the brand had honed its design and technological aspects further. The W2007 is characterized by its stunning visual aesthetics, often featuring unique inlays and a glossy finish that not only enhances its beauty but also adds durability. The soundboard of the W2007 is crafted using a combination of solid woods, with some variations offering premium options like cedar. This model emphasizes tonal clarity and dynamic range, ideal for fingerstyle playing or strumming chords with equal finesse.

In summary, the Woodstock W2005, W2006, and W2007 each brought distinct features and advancements, catering to the diverse needs of musicians. From solid wood construction and sustainable practices to advanced electronics and striking finishes, the Woodstock series reflects an evolution of craftsmanship and a dedication to creating instruments that inspire creativity and passion in every performance.
Top Page Image Contents