DeVillbiss Air Power Company MG1-UMCCOMP-3 warranty

Page 7

INSTALLATION AND BREAK-IN

PROCEDURES

Grounding Instructions

Additional Regulators and Controls

RISK OF ELECTRICAL SHOCK! IN THE EVENT OF A SHORT CIRCUIT, GROUNDING REDUC- ES THE RISK OF SHOCK BY PROVIDING AN ESCAPE WIRE FOR THE ELECTRIC CURRENT. THIS AIR COMPRESSOR MUST BE PROPERLY GROUNDED.

The air compressor is equipped with a cord having a grounded wire with an appropriate grounding plug. The plug must be used with an outlet that has been installed and grounded in accordance with all local codes and ordinances. The outlet must have the same configuration as the plug. See illustration. DO NOT USE AN ADAPT-

ER.

Inspect the plug and cord before each use. Do not use if there are signs of damage.

IMPROPER GROUNDING CAN RESULT IN ELECTRICAL SHOCK.

Do not modify the plug that has been provided. If it does not fit the available outlet, the correct outlet should be installed by a qualified electrician.

If repairing or replacing cord or plug, the grounding wire must be kept separate from the current-carrying wires. Never connect the grounding wire to a flat blade plug terminal. The grounding wire has insulation with an outer surface that is green - with or without yellow stripes.

If these grounding instructions are not completely under- stood, or if in doubt as to whether the compressor is properly grounded, have the installation checked by a qualified electrician.

Since the air tank pressure is usually greater than that which is needed, a regulator is employed to control the air pressure ahead of any individual air driven device.

Separate air transformers which combine the function of air regulation, moisture and dirt removal should be used where applicable.

Break-in Procedures

Serious damage may result if the following break-in instructions are not closely followed.

This procedure is required:

1.Before the air compressor is put into service.

2.When the check valve is replaced.

a.Set the pressure switch lever to the "OFF" position.

b.Plug the power cord into the correct branch circuit receptacle.

c.Turn the regulator clockwise, opening it fully, to prevent air pressure build-up in the tank.

d.Move the pressure switch lever to "ON/AUTO". The compressor will start.

e.Run the compressor for 15 minutes. Make sure the regulator is open and there is no tank pressure build-up.

f.After 15 minutes, close the regulator by turning knob counterclockwise. The air receiver will fill to cut-out pressure and the motor will stop. The compressor is now ready for use.

7 - ENG

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Permanently Lubricated AIR Compressor Limited Warranty ONE Year from Date of Purchase Important Safety Instructions Ventilation Risk from Moving Pressure Switch is in the onNever Inhale AIR From Risk to BreathingON-RECEIPT Inspection GlossaryDuty Cycle General InformationDescription of Operation Installation and BREAK-IN ProceduresGrounding Instructions Additional Regulators and Controls Storage Operating ProceduresTroubleshooting Guide Troubleshooting Guide Permanently Lubricated AIR Compressor Service Notes DeVilbiss Air Power Company 213 Industrial Drive Jackson, TN

MG1-UMCCOMP-3 specifications

DeVilbiss Air Power Company has long been a trusted name in the air-powered tools and equipment industry, and the MG1-UMCCOMP-3 model is no exception. This air compressor combines advanced technology with robust design, making it ideal for a variety of applications, ranging from automotive to woodworking.

The MG1-UMCCOMP-3 is equipped with a powerful motor that ensures efficient performance. With a horsepower rating designed to deliver consistent air pressure, the compressor can tackle demanding tasks with ease. Its compact design allows for versatile placement in workshops, garages, or job sites, while still providing an impressive output.

One standout feature of this model is its user-friendly controls, which make it accessible even for those who may not be familiar with operating air compressors. The gauges are clearly marked and easy to read, providing real-time feedback on pressure levels. This ensures that users can maintain optimal operating conditions and avoid any potential issues.

Another key characteristic of the MG1-UMCCOMP-3 is its quiet operation. This model has been engineered with noise-reduction technologies, making it significantly quieter than many traditional compressors. This feature is particularly beneficial for environments where noise levels need to be kept to a minimum, such as residential areas or enclosed workspaces.

Durability is a hallmark of DeVilbiss products, and the MG1-UMCCOMP-3 is built to withstand rigorous use. The components are made from high-quality materials, ensuring that the compressor can handle the wear and tear that comes with frequent operation. Its sealed design also helps protect against dust and debris, prolonging the lifespan of the machine.

Moreover, the MG1-UMCCOMP-3 includes safety features that prioritize user protection. An automatic shut-off function prevents overheating, and safety valves have been integrated to relieve pressure in case of excessive build-up. These features help ensure that users can operate the compressor with confidence and peace of mind.

In summary, the DeVilbiss Air Power Company MG1-UMCCOMP-3 air compressor stands out in the market with its powerful motor, user-friendly interface, quiet operation, and durable construction. Its combination of safety and efficiency makes it a top choice for both professional and amateur users alike, streamlining tasks and enhancing productivity across various applications. Whether you're inflating tires, operating pneumatic tools, or working on intricate projects, this air compressor provides the reliability needed for successful completion.
Top Page Image Contents