Panasonic SC-AK750 Connecting and playing a USB mass Storage class device, Changing the main unit

External unit (continued)

Connecting and playing a USB mass

storage class device

ESPAÑOL	The USB connectivity enables you to connect and play
	MP3 tracks from USB mass storage class. Typically, USB
	memory devices. (Bulk only transfer)
	Preparation
	Before connecting any USB mass storage device to the unit,
	ensure that the data stored therein has been backed up.
	It is not recommended to use a USB extension cable. The
	USB device is not recognised by this unit.

DANSK	USB enabled device
	(not included)
	It is not recommended
	to use a USB extension
	cable. The device
	connected via the cable
	will not be recognised by
	this unit.

1 Reduce the volume and connect the USB mass storage device.

2 Press [6, USB] to start play.

FRANÇAIS	To	Action
	pause play	Press [6, USB].
		Press again to resume play.
	USB
	stop play	Press [7, CLEAR].
		“RESUME” is displayed. The position is
		memorized.
		Press [6, USB] to resume.
		Press [7, CLEAR] again to clear the position.
	skip tracks	Press [4, / REW] or [¢, / FF].
- 4
LANG	skip album	Press [ALBUM (	or	)] in the play mode.
		Press [ALBUM (	or	)] once and then
		the numeric buttons in the stop mode.

For other operating functions, they are similar as those described in “Discs” (\ page 9 ~ 11).

				Recording from a USB mass
				storage class device
5		1 Press [4, / REW ] or [¢, / FF] to select the
			desired track for recording.
-	2		Press [¶, REC] on the main unit to start recording.
LANG
RQTV0205
16

RQT8043

Compatible devices

Devices which are defined as USB mass storage class:

•USB devices that support bulk only transfer.

•USB devices that support USB 2.0 full speed.

Supported format

Files must have the extension “.mp3” or “.MP3”.

Note:

•CBI (Control/Bulk/Interrupt) is not supported.

•A device using NTFS fi le system is not supported [Only FAT 16/32 (File Allocation Table 16/32) fi le system is supported].

•Depending on the sector size, some fi les may not work.

•This unit can access up to 255 albums (including blank folders) and 2500 tracks.

•The maximum number of tracks in a folder are 999 tracks.

•Only one memory card will be selected when connecting a multiport USB card reader. Typically the fi rst memory card inserted.

•Disconnect the USB card reader from the unit when you remove the memory card. Failure to do so may cause malfunction to the device.

•When you connect your digital audio player to the USB port, it charges all the time except in standby mode or during tape recording.

MUSIC PORT	Changing the main unit and
	remote control mode

The remote control and main unit are factory-set to “REMOTE 1” mode.

If your remote control affects other equipment during operation, you can switch to operate in “REMOTE 2” mode.

To switch to “REMOTE 2” mode

1	While pressing and holding [MUSIC PORT] on the main
	unit
	Press and hold [2] until “REMOTE 2” appears on
	the main unit display.
2	Press and hold [ENTER] and [2] for at least 2

seconds.

The main unit and remote control are now set to operate in “REMOTE 2” mode.

To return to “REMOTE 1” mode

Perform steps 1 and 2 above but use [1] instead of [2] for both steps. (“REMOTE 1” appears on the main unit during step 1.)

The remote control cannot work with the main unit if their modes are different.

“REMOTE 1” or “REMOTE 2” appears on the main unit display when you operate the remote control.∗

∗If “REMOTE 1” appears (The main unit is in “REMOTE 1” mode.)

Press and hold [ENTER] and [1] on the remote control for at least 2 seconds.

If “REMOTE 2” appears (The main unit is in “REMOTE 2” mode.)

Press and hold [ENTER] and [2] on the remote control for at least 2 seconds.

RQTV0205-B.indd 16 2/22/07 7:02:53 PM