Operation, Charging Battery Pack, To Charge

OPERATION

WARNING:

Do not allow familiarity with the drill-driver to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury.

CHARGING BATTERY PACK

The battery pack for this tool has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it until the light on front of charger changes from flashing green to continuous green.

Note: Batteries will not reach full charge the first time they are charged. Allow several cycles (drilling followed by recharging) for them to become fully charged. This is normal for nickel-cadmium batteries.

TO CHARGE

nCharge battery pack only with the charger provided.

nMake sure power supply is normal house voltage, 120 volts, 60 Hz, AC only.

nConnect the charger to a power supply.

nAttach battery pack to charger by aligning raised ribs on battery pack with grooves in charger, then slide battery pack onto charger. See Figure 2.

nAfter normal usage, 30 minutes of charging time is required to be fully charged.

nThe battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem.

nDo not place charger in an area of extreme heat or cold. It will work best at normal room temperature.

nWhen the batteries become fully charged, unplug your charger from power supply and remove the battery pack.

IMPORTANT INFORMATION FOR RECHARGING HOT BATTERY PACK

When using this drill continuously, the batteries in the bat- tery pack will become hot. The battery pack for this tool will charge more rapidly and efficiently when at a cooled temperature.

The internal fan for this charger will automatically turn on when a battery pack is inserted. Air circulates through the battery, bringing it to optimum charging temperature, de- creasing the time required to begin fast charging the pack, and extending the life of the battery.

Note: The fan will start to run and continue to run until the battery pack is removed from the charger.

When the battery pack becomes discharged and is hot, the green LED will be off and the red LED will begin flashing.

When the battery pack cools down to approximately 104°F (40°C), the charger will automatically begin fast charge mode.

Fig. 2

If the Red LED continues to flash for more than 90 minutes, and the green LED remains off, this may indicate a damaged battery that will not charge.

IMPORTANTINFORMATIONFORRECHARGING COOL BATTERY PACK

If battery pack is below normal temperature range, the red LED will begin flashing and the green LED will be off. When the battery warms to a temperature of more than 41°F (5°C), the charger will automatically begin fast charge mode.

Note: Refer to "CHARGING BATTERY PACK" for normal recharging of batteries. If the charger does not charge your battery pack under normal circumstances, return both the battery pack and charger to your nearest repair center for electrical check. For the location of your nearest repair cen- ter, please call 1-866-539-1710.

CAUTION:

To prevent damage to battery pack, remove battery pack from charger immediately if no LED comes on. Return battery pack and charger to your nearest service center for checking or replacing. Also, if you are removing battery pack from charger and no LEDs are on, return both battery pack and charger to your nearest service center. Do not insert another battery pack into charger. A damaged charger may damage a battery pack.

R82015 specifications

The RIDGID R82015 is a cordless drill/driver that stands out in the comprehensive line of power tools designed for both professionals and DIY enthusiasts. Known for its durability and performance, the R82015 embodies RIDGID’s commitment to delivering high-quality tools equipped with advanced features.

One of the key highlights of the RIDGID R82015 is its powerful motor, capable of delivering an impressive 2,000 RPM on high speed and 0-450 RPM on low speed. This variable speed feature allows users to tackle a wide range of applications, from delicate tasks to heavy-duty jobs, with ease and precision. The drill is equipped with a two-speed transmission that optimizes performance based on the specific requirements of the task at hand.

An integral part of the R82015’s design is its 1/2-inch keyless chuck, which allows for quick bit changes without the need for additional tools. This feature enhances user convenience, saving valuable time during projects. The drill’s high torque output of up to 400 inch-pounds ensures that it can handle tough fastening and drilling applications effortlessly.

Another significant advantage of the RIDGID R82015 is its heavy-duty construction, designed to withstand the rigors of job site conditions. The ergonomic handle is molded for comfort and includes a rubber overmold for a secure grip, reducing fatigue during prolonged use. This design consideration ensures that users can work efficiently without sacrificing comfort.

Additionally, the RIDGID R82015 incorporates Smart Technology, which adds to its versatility. This intuitive technology optimizes battery management and ensures consistent power output. Compatible with RIDGID's 18V battery system, it allows users to interchange batteries with other tools in the RIDGID lineup, enhancing overall productivity.

The built-in LED light is another commendable feature, illuminating dark workspaces and providing users with enhanced visibility during drilling tasks. This added convenience often proves invaluable when working in tight or dimly lit areas.

In summary, the RIDGID R82015 combines power, versatility, and durability, making it an outstanding choice for professionals and hobbyists alike. Its robust motor, user-friendly features, and advanced technologies position it as a reliable tool that can be relied upon for a myriad of tasks, from simple home repairs to complex construction projects. With RIDGID’s reputation for quality, the R82015 is a tool that ensures efficient and effective performance, solidifying its place in any toolkit.