RIDGID R5010 manual General Safety Rules, Work Area, Electrical Safety, Personal Safety

Page 3

GENERAL SAFETY RULES

WARNING:

Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

Work Area

￿Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

￿Do not operate power tools in explosive atmo- spheres, such as in the presence of flammable liq- uids, gases, or dust. Power tools may create sparks which may ignite the dust or fumes.

￿Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.

Electrical Safety

￿Double insulated tools are equipped with a polar- ized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug

in any way. Double insulation eliminates the need for the three-wire grounded power cord and grounded power supply system.

￿Avoid body contact with grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded.

￿Don’t expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of elec- tric shock.

￿Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges, or moving parts. Replace damaged cords immediately.

￿When operating a power tool outside, use an out- door extension cord marked “W-A” or “W”. These cords are rated for outdoor use and reduce the risk of electric shock.

￿Damaged cords increase the risk of electric shock.

Personal Safety

￿Stay alert, watch what you are doing and use com- mon sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.

￿Dress properly. Do not wear loose clothing or jew- elry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jew- elry, or long hair can be caught in moving parts.

￿Avoid accidental starting. Be sure switch is off be- fore plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on, in- vites accidents.

￿Remove adjusting keys or wrenches before turn- ing the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal in- jury.

￿Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.

￿Use safety equipment. Always wear eye protection. Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

￿Do not use on a ladder or unstable support.

￿Loose clothes, jewelry, or long hair can be drawn into air vents.

Tool Use and Care

￿Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.

￿Do not force tool. Use the correct tool for your ap- plication. The correct tool will do the job better and safer at the rate for which it is designed.

￿Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired.

￿Disconnect the plug from power source before mak- ing any adjustments, changing accessories, or stor- ing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally.

￿Store idle tools out of the reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.

￿Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cut- ting edges are less likely to bind and are easier to con- trol.

￿Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.

￿Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool.

3

Image 3
Contents Operators Manual Introduction Table of ContentsWork Area General Safety RulesElectrical Safety Personal SafetySpecific Safety Rules ServiceAdditional Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsExtension Cords SpecificationsElectrical Double InsulationPacking List UnpackingApplications InstructionsFeatures Operation LOCK-ON ButtonKeyless Chuck TWO-SPEED Gear Shift Knob Variable SpeedFollow these steps to adjust the auxiliary handle assembly Adjusting the Depth Gauge RODTo Remove Bits To Install BitsHelpful Hints DrillingTo Retighten a Loose Chuck Chuck RemovalMaintenance GeneralLubrication HOW to Obtain Service What is not Covered WarrantyDAY Satisfaction Guarantee Policy What is Covered Under the Limited Three Year WarrantyPage Customer Service Information