RIDGID TS2400, AC9930 manual Portable Power Tools with a Small Base, See Figures 16, 17

Page 10

ASSEMBLY

SEE BOLT VIEW A

SEE BOLT VIEW B

Fig. 14

 

nRemove mounting blocks from table. Attach power tool to mounting blocks with 1/4-20 carriage bolts, washers, lockwashers and nuts as shown. Reinstall mounting blocks to work stand table.

NOTE: See views of bolt recommendations, see figure 15.

2 X 6

POWER

TOOL

WORK

STAND

BOLT VIEW A

BOLT VIEW B

(2 X 6s WORK STAND)

(POWER TOOL TO 2 X 6s)

 

Fig. 15

 

 

Portable Power Tools with a Small Base

See Figures 16, 17 and 18.

(Tool mounting holes do not span 2 x 6 mounting blocks shown.)

nPlace the stand in the set-up position as shown.

nUsing the stand’s table as a pattern, locate the 2 x 6 s as shown, and from the bottom mark hole locations.

nDrill 1/4 in. or 3/8 in. diameter holes in the two 2 x 6 x 24 in. long mounting blocks as shown.

SET-UP POSITION

Fig. 16

nTemporarily attach the mounting blocks to work stand with the supplied bolts or 1/4-20 bolts at least 2-1/2 in. long. Secure with washers, lockwashers and nuts.

nLocate and drill holes in 2 x 6 mounting blocks and 1 x 4 cross pieces, as shown. Plywood 3/4 in. thick, 24 in. x 27 in. may be used in place of the 1 x 4 s.

nLoosen 2 x 6 mounting blocks from work stand table. Attach two 1 x 4 cross pieces to the mounting blocks with 1/4-20 carriage bolts at least 2.75 inches long, as shown. Secure with washers, lockwashers and nuts.

NOTE: A 5/8” diameter counterbore 1/4” deep is required for clearance between the bolt head and the

SEE BOLT

PLYWOOD

SEE BOLT

VIEW A

 

VIEW A-1

SEE BOLT

SEE BOLT

 

VIEW B

Fig. 17

VIEW C

 

 

 

 

work stand table. Tap carriage bolt with hammer to seat bolt fully into the hole and counterbore. Resecure 2x6 mounting blocks to work stand table.

If using plywood, the supplied 1/4-20 bolts may be used to attach the 2 x 6s and plywood to the work stand table. When mounting table saws to plywood an opening for the sawdust to fall through is needed. See your tools owner’s manual for recommended hole size.

See views of bolt recommendations, see figure 18.

n To attach power tool, locate and drill holes in cross pieces.

nAttach power tool to cross pieces with 1/4-20 carriage bolts as shown with washers, lockwashers and nuts.

 

BOLT VIEW A

WORK

BOLT VIEW A-1

(2 X 6s TO WORK STAND)

(PLYWOOD AND 2 X 6s

 

2 X 6

STAND

TO WORK STAND)

 

 

2 X 6

 

 

 

 

 

POWER

1 X 4 OR

 

1 X 4

TOOL

PLYWOOD

 

 

2 X 6

 

2 X 6

 

BOLT VIEW C

 

BOLT VIEW B

 

(POWER TOOL TO

 

 

1X4s OR

(1 X 4s TO 2 X 6s)

WORK STAND

Fig. 18

 

 

 

 

 

 

 

10

Image 10
Contents OPERATOR’S Manual Table of Contents IntroductionRules for Safe Operation Read ALL InstructionsSymbols Safety and International SymbolsLoose Parts UnpackingTools Needed Moving the Carry Handle Spring PIN AssemblyAssembling the Lower Foot See FigureBefore you start Setting UpWork Stand SET-UP See Figures 4, 5, 6See Figures 8, 9, 10 Work Stand Fold DownFolding Down LowerRidgid 10-in. Table Saw Model TS2400 Mounting Power ToolsOther Portable Power Tools with a Large Base SET-UP PositionPortable Power Tools with a Small Base See Figures 16, 17Exploded VIEW/REPAIR Parts Work-N-Haul Ittm Two Wheel Work Stand Model AC9930Customer Service Information