RIDGID R885 manual LED Function of Ridgid NICKEL-CADMIUM Chargers, RED LED Green LED

Page 15

OPERATION

LED FUNCTION OF RIDGID NICKEL-CADMIUM CHARGERS

See Figure 7.

LED

BATTERY

RED

GREEN

ACTION

INDICATOR

PACK

LED

LED

 

Power

Without battery pack

ON

OFF

Ready to charge battery pack

 

 

 

 

When battery pack reaches cooled

Evaluate

Hot battery pack

Flashing

OFF

temperature, charger begins fast

 

 

 

 

charge mode.

 

 

 

 

When battery pack reaches warmed

Evaluate

Cold battery pack

Flashing

OFF

temperature, charger begins fast

 

 

 

 

charge mode.

 

 

 

 

Charger pre-charges battery until

Evaluate

Deeply discharged

Flashing

OFF

normal voltage is reached, then

 

 

 

 

begins fast charge mode.

Defective

Defective

Flashing

Flashing

Battery pack or charger is defective

• If defective, try to repeat the conditions a second time by removing and reinstalling the battery pack. If the LED status repeats a second time, try charging a different battery.

• If a different battery charges normally, dispose of the defective pack (see Maintenance section).

• If a different battery also indicates “Defective,” the charger may be defective.

 

 

Charging

Fast charging

ON

Flashing

See chart below for charge times

 

 

 

 

 

 

 

 

 

Full

Slow charging

OFF

ON

Fast charging is complete;

 

 

 

 

 

 

charger maintains charge mode

 

 

 

 

 

 

 

 

 

 

 

 

 

RED LED

GREEN LED

POWER

 

 

INDICATOR

EVALUATE

INDICATOR

DEFECTIVE

INDICATOR

CHARGING

INDICATOR

FULL

INDICATOR

BATTERY

AVERAGE CHARGE TIME

 

 

COMPACT SERIES

18 min.

 

 

HC

27 min.

 

 

HC 2.5

34 min.

 

 

Fig. 7

15

Image 15
Contents OPERATOR’S Manual Introduction Table of ContentsPersonal Safety General Safety RulesWork Area Safety Electrical SafetyCauses and Operator Prevention of Kickback Specific Safety RulesBattery Tool USE and Care ServiceAdditional Safety Rules Safety Rules for Charger Important Safety InstructionsName DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning Width CUT Scale Depth Adjustment Lever FeaturesTrigger 24V LITHIUM-ION Battery Pack 18V NICKEL-CADMIUM Battery PackAssembly Spindle Lock Button HEX KEY Tighten Loosen Attaching the BladeRemoving the Blade BladeApplications Charging the Battery PackCharge Level Indicator OperationTo Charge Charge Level IndicatorCharging a HOT Battery Pack Charging a Cool Battery PackVolts, 60 Hz, AC only LED Function of Ridgid 24V LITHIUM-ION ChargerRED LED Green LED Evaluate Indicator DefectiveIndicator Full Battery Average Charge Time LED Function of Ridgid NICKEL-CADMIUM ChargersBlade Guard System To Install Battery PackTo Remove Battery Pack SAW BladesIn. MAX KickbackSee Figures 10 Kickback Blade SET TOO Deep Incorrect Support WrongIndexable Levers Depth of CUT AdjustmentTo Adjust Blade Depth STARTING/STOPPING the SAWRight Wrong Operating the SAWSee Figures 17 To make the best possible cutTOP View of SAW Front of SAW Using AN Edge GuideCross CUTTING/RIP Cutting See Figures 19Bevel To Adjust Bevel SettingBevel Cutting See Figures 23To Adjust 0 Bevel Stop Bevel StopPocket Cutting Batteries MaintenanceGeneral Maintenance Battery Pack Removal and Preparation for RecyclingAccessories HOW to Obtain Service What is not Covered WarrantyDAY Satisfaction Guarantee Policy What is Covered Under the 3 Year Limited Service WarrantyModel No R885 Serial No Customer Service Information