RIDGID MS1290LZA manual Loose Parts, Dust BAG, Flat Head Socket CAP Screw

Page 14

LOOSE PARTS

The following items are included with your miter saw:

Dust Bag

Dust Bag Frame

Dust Guide

Work Clamp

DUST BAG

DUST BAG	LASER
FRAME	GUIDE

FLAT HEAD

SOCKET CAP

SCREW

Blade Wrench

Hex Key, 1/16 in.

Laser Guide

Flat Head Socket Cap Screw

Operator’s Manual (not shown)

WORK CLAMP

HEX KEY,

1/16 in.

BLADE

WRENCH

DUST

GUIDE

Fig. 7

WARNING:

The use of attachments or accessories not listed in this manual might be hazardous and could cause serious personal injury.

Image 14

Contents OPERATOR’S Manual MS1290LZATable of Contents Introduction Blade Coasts After Being Turned OFF General Safety RulesRead ALL Instructions Specific Safety Rules  Before Making a CUT, be Sure ALL ADJUST- Ments are SecureSpecific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Symbol Signal MeaningDouble Insulation Cord Length Wire Size A.W.GElectrical Electrical ConnectionGlossary of Terms Features Product SpecificationsAMP Motor Know Your Compound Miter SAW12 IN. Blade Bevel Lock LeverMiter Scale Switch TriggerMiter Lock Lever Miter ThumbwheelCombination Square Tools NeededRatchet Phillips Screwdriver Framing SquareFlat Head Socket CAP Screw Loose PartsDust BAG Work Clamp HEX KEY Blade Wrench Dust GuideMounting Holes AssemblyUnpacking SAW ARM Using the Depth GuideLocking / Unlocking the SAW ARM Depth GuideDust BAG Frame Guide Exhaust Port Installing the Dust BAGInstalling the Work Clamp Work ClampInstalling / Replacing the Blade To Cut the Mark Aligning the Laser Guide LineRemoving the Mark To Leave the MarkRemoving / Replacing the Zero CLEAR- Ance Throat Plate Centering the SAW Blade Between the Slide BarsSquaring the SAW Blade to the Fence Adjusting the Miter Lock LeverTo adjust See Figures 17Indicator Fig View of Blade Square with Fence Miter ScaleTravel Pivot Adjustment Adjusting the Bevel Lock LeverAdjusting the Bevel Pivot Bevel Lock Lever Lift to UnlockSee Figures 27 IndicatorSquaring the Blade to the Miter Table Sliding Miter FenceCutting with Your Sliding Compound Miter SAW OperationApplications Slide CUT Slide SAW ARM Forward then Push Down Back To Slide CUTSee Figures 31 Work Clamp To Miter CUT / Cross CUTSee Figures 33 Cross CUT Work Clamp Miter CUTSee Figures 35 Scale Indicator BevelTo Bevel CUT Bevel CUT Clamp Lock PINTo Compound Miter CUT Compound Miter CUTLong Workpiece Supporting Long WorkpiecesClamping Wide Workpieces 45 x 45 Compound Miter CUTDepth Guide CUT These Grooves With SAW Using AN Auxiliary FenceRough Cutting a Dado Auxiliary FencePitch Side COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters Ceiling Cutting Crown MoldingLaying Molding Flat on the Miter Table Inside Corner FenceCrown Molding JIG Using a Crown Molding Support JIGMaking a Crown Molding Support JIG Adjustment Screw Laser Button Aperture HEX KEY Mark AdjustmentsTo Adjust the Laser Guide Cutting Warped MaterialBrush Replacement MaintenanceGeneral Maintenance LubricationMotor Belt Tension To adjust belt tensionScrew Battery Cover Batteries Negative Changing the BatteriesAccessories Miter Saw Utility VehicleWhat is Covered Under the 3 Year Limited Service Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not CoveredMS1290LZA Customer Service InformationModel No Serial No