RIDGID MS1290LZA manual Double Insulation, Electrical Connection, Extension Cords

Page 8

ELECTRICAL

DOUBLE INSULATION

Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protect- ing insulation. Double insulated tools do not need to be grounded.

WARNING:

The double insulated system is intended to protect the user from shock resulting from a break in the tool’s internal wiring. Observe all normal safety precautions to avoid electrical shock.

NOTE: Servicing of a product with double insulation requires extreme care and knowledge of the system and should be performed only by a qualified service technician. For service, we suggest you return the tool to your nearest authorized service center for repair. Always use original factory replace- ment parts when servicing.

ELECTRICAL CONNECTION

This tool has a precision-built electric motor. It should be connected to a power supply that is 120 volts, 60 Hz, AC only (normal household current). Do not operate this tool on direct current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If the tool does not operate when plugged into an outlet, double-check the power supply.

EXTENSION CORDS

When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the current the product will draw. An undersized cord will cause a drop in line voltage, resulting in overheating and loss of power. Use the chart to determine the minimum wire size required in an extension cord. Only round jacketed cords listed by Underwriter’s Laboratories (UL) should be used.

When working outdoors with a product, use an extension cord that is designed for outside use. This type of cord is designated with “WA” on the cord’s jacket.

Before using any extension cord, inspect it for loose or exposed wires and cut or worn insulation.

**Ampere rating (on product data plate)

0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0

Cord Length

 

Wire Size (A.W.G.)

 

 

 

 

 

 

 

 

 

25'

16

16

16

16

14

14

 

 

 

 

 

 

 

50'

16

16

16

14

14

12

 

 

 

 

 

 

 

100'

16

16

14

12

10

—

**Used on 12 gauge - 20 amp circuit. NOTE: AWG = American Wire Gauge

WARNING:

Keep the extension cord clear of the working area. Position the cord so that it will not get caught on lumber, tools, or other obstructions while you are working with a power tool. Failure to do so can result in serious personal injury.

WARNING:

Check extension cords before each use. If dam- aged replace immediately. Never use tool with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents OPERATOR’S Manual MS1290LZATable of Contents Introduction Blade Coasts After Being Turned OFF General Safety RulesRead ALL Instructions Specific Safety Rules  Before Making a CUT, be Sure ALL ADJUST- Ments are SecureSpecific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Symbol Signal MeaningCord Length Wire Size A.W.G ElectricalDouble Insulation Electrical ConnectionGlossary of Terms Features Product SpecificationsKnow Your Compound Miter SAW 12 IN. BladeAMP Motor Bevel Lock LeverSwitch Trigger Miter Lock LeverMiter Scale Miter ThumbwheelTools Needed RatchetCombination Square Phillips Screwdriver Framing SquareLoose Parts Dust BAGFlat Head Socket CAP Screw Work Clamp HEX KEY Blade Wrench Dust GuideMounting Holes AssemblyUnpacking Using the Depth Guide Locking / Unlocking the SAW ARMSAW ARM Depth GuideInstalling the Dust BAG Installing the Work ClampDust BAG Frame Guide Exhaust Port Work ClampInstalling / Replacing the Blade Aligning the Laser Guide Line Removing the MarkTo Cut the Mark To Leave the MarkRemoving / Replacing the Zero CLEAR- Ance Throat Plate Centering the SAW Blade Between the Slide BarsAdjusting the Miter Lock Lever To adjustSquaring the SAW Blade to the Fence See Figures 17Indicator Fig View of Blade Square with Fence Miter ScaleAdjusting the Bevel Lock Lever Adjusting the Bevel PivotTravel Pivot Adjustment Bevel Lock Lever Lift to UnlockIndicator Squaring the Blade to the Miter TableSee Figures 27 Sliding Miter FenceCutting with Your Sliding Compound Miter SAW OperationApplications Slide CUT Slide SAW ARM Forward then Push Down Back To Slide CUTSee Figures 31 To Miter CUT / Cross CUT See Figures 33Work Clamp Cross CUT Work Clamp Miter CUTScale Indicator Bevel To Bevel CUTSee Figures 35 Bevel CUT Clamp Lock PINTo Compound Miter CUT Compound Miter CUTSupporting Long Workpieces Clamping Wide WorkpiecesLong Workpiece 45 x 45 Compound Miter CUTUsing AN Auxiliary Fence Rough Cutting a DadoDepth Guide CUT These Grooves With SAW Auxiliary FencePitch Side COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters Cutting Crown Molding Laying Molding Flat on the Miter TableCeiling Inside Corner FenceCrown Molding JIG Using a Crown Molding Support JIGMaking a Crown Molding Support JIG Adjustments To Adjust the Laser GuideAdjustment Screw Laser Button Aperture HEX KEY Mark Cutting Warped MaterialMaintenance General MaintenanceBrush Replacement LubricationTo adjust belt tension Screw Battery Cover Batteries NegativeMotor Belt Tension Changing the BatteriesAccessories Miter Saw Utility VehicleWarranty DAY Satisfaction Guarantee PolicyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredCustomer Service Information Model NoMS1290LZA Serial No
Top Page Image Contents