RIDGID BS14002 manual Assembly, Unpacking, Attaching Leveling Feet

Page 15

ASSEMBLY

UNPACKING

This product requires assembly.

nCarefully remove the tool and any accessories from the box. Place it on a level work surface.

NOTE: This tool is heavy. To avoid back injury, lift with your legs, not your back, and get help when needed.

nInspect the tool carefully to make sure no breakage or damage occurred during shipping.

nDo not discard the packing material until you have carefully inspected the tool, identified all loose parts, and satisfactorily operated the tool.

nRemove the protective oil that is applied to all unpainted metal surfaces. Use any ordinary household type grease and spot remover.

nApply coat of paste wax to the saw table.

nThe saw is factory set for accurate cutting. After assem- bling it, check for accuracy. If shipping has influenced the settings, refer to specific procedures explained in the operation and maintenance sections of this manual.

nIf any parts are damaged or missing, please call 1-866-539-1710 for assistance.

WARNING:

If any parts are missing, do not operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury.

nPut the leveling feet through the holes in the bottom of each leg.

nThread another hex nut on each of the leveling feet and hand tighten until they are next to the bottom support of the leg.

LEG

HEX NUTS

LEVELING FOOT

Fig. 10

WARNING:

To reduce the risk of injury from unexpected saw or work movement, leveling feet must be adjusted so that saw does not rock. After the band saw has been attached to the leg stand, it will be necessary to adjust the leveling feet.

WARNING:

Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.

WARNING:

Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious personal injury.

ATTACHING LEVELING FEET

See Figure 10.

nLocate the following items:

4 leveling feet

8 hex nuts, (3/8-16)

nFrom the loose parts find the following items:

4 legs

nThread a hex nut on each of the leveling feet and screw it down towards the rubber foot.

CARRIAGE

WASHERS

BOLT

LOCK WASHERS

 

 

HEX NUTS

 

LEG BRACE

 

(SHORT)

LEG BRACE

LEG

(LONG)

 

BASE

Fig. 11

15

Image 15
Contents OPERATOR’S Manual Introduction Table of ContentsRead ALL Instructions General Safety RulesDo not Remove Jammed Cutoff Pieces until blade has stopped Specific Safety RulesSymbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceKerf Glossary of TermsGrounding Instructions Speed and WiringElectrical Extension CordsSee Figures 2 Changing Motor VoltageSpecifications FeaturesBlade Tension Knob Blade Guard Adjustment KnobsHousing Covers Know Your Band SAWTools Needed Following items are included with your band saw Loose PartsSAW Table Trunnion Support Assembly UnpackingAttaching Leveling Feet Assembling LEG Stand Mounting Band SAW to LEG StandSee Figures 11 Mounting the Motor Assembly Installing the V-BELTSee Figures 15 Mounting the Pulley Cover Mounting Blade HangersMounting the Switch BOX Mounting the Dust ChuteMounting the Table Trunnion Support to Band SAW Installing Bevel Scale Indicator Mounting the SAW Table to SAW BodySee Figures 25 Adjusting Blade Tension Tracking the BladeSee Figures 27 Squaring the SAW Table to the Blade Adjusting Table StopSee Figures 33 Adjusting Upper Blade Guide AssemblyAdjusting Upper Blade Guides and Thrust Bearing See Figures 32See Figures 35 Adjusting Lower Blade Guides and Thrust BearingOperation Locking the Switch Avoiding InjuryBefore Leaving the SAW Circle Cutting Tilting the TableAdjustments Installing and Adjusting the BladeSee Figures 40 Lock Unlock To Raise To Lower Adjusting Blade Guide AssemblyTires MaintenanceGeneral Maintenance MOTOR/ELECTRICALBrush LubricationTroubleshooting AccessoriesProblem Cause Page HOW to Obtain Service What is not Covered WarrantyDAY Satisfaction Guarantee Policy What is Covered Under the 3 Year Limited Service Warranty14 in. Band SAW Customer Service Information