RIDGID MS1250LZ manual Table Extension, Mounting the Miter SAW to the LEG Stand, HEX Bolt NUT

Page 16

ASSEMBLY

UPPER

BRACE (A)

UPPER SIDE

BRACE (C)

LEG (B)

		TABLE
		EXTENSION
LOWER SIDE	LOWER	WASHER
LOWER SIDE	BRACE (E)	WASHER
BRACE (D)
LEG STAND ASSEMBLED		SOCKET HEAD	WASHER
LEG STAND ASSEMBLED		SCREW	Fig. 11
	Fig. 10	SCREW	Fig. 11
	Fig. 10

TABLE EXTENSION

See Figure 11.

The table extension can be used on the left side of the miter saw. To assemble and install the table extension:

nInsert socket head screw and washer into the two holes in the side of the miter saw base.

nTighten securely.

MOUNTING THE MITER SAW TO THE LEG STAND

See Figure 12.

nTurn leg stand upright as shown in figure 10.

nCarefully place miter saw on top of leg stand. Align holes in the miter saw base with holes in leg stand.

nInsert the 5/16-18 x 2-1/2 in. hex bolts in each of the four holes and secure using hex nuts.

nTighten all hardware with a wrench. You may find it helpful to use one wrench to hold the head of the bolt and one to tighten the hex nut.

HEX

BOLT

HEX

NUT

Fig. 12

Image 16

Contents OPERATOR’S Manual Table of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules Specific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Symbol Signal MeaningCord Length Wire Size A.W.G ElectricalDouble Insulation Electrical ConnectionGlossary of Terms Product Specifications FeaturesMiter Switch Trigger Know Your Compound Miter SAWAMP Motor 12 IN. BladeTools Needed Dust Guide HEX Bolt Loose PartsSocket Head Screws Washer Extention Dust BAG Blade Wrench Assembly UnpackingMounting Holes Trace Holes AT These Locations For Hole Pattern SAW BaseAssembling LEG Stand See Figures 9Upper Side Brace C LEG B Lower Brace D HEX NUT Rubber Foot Upper Brace a LEG B Lower Brace E Carriage BoltTable Extension Mounting the Miter SAW to the LEG StandUpper Brace a Upper Side Brace C LEG B Extension Socket Head Washer ScrewDust BAG Dust GuideWork Clamp Screw Blade Bolt Cover Lower Guard To Install BladeLaser Guide Mounting the Exactline Laser Guide Aligning the Laser Guide LineCutting a Slot in the Zero Clearance Throat Plate Squaring the SAW Blade to the FenceSee Figures 20 Broken RED LineAdjustments are Required Sliding Miter Fence Blade Squaring the Blade to the Miter Table See Figures 25Lock Knob CombinationPivot Adjustments Travel Pivot Adjustment Bevel Pivot AdjustmentOperation ApplicationsTo Crosscut Cutting with Your Compound Miter SAWStraight Crosscut Work Clamp Bevel Scale Indicator Indicator Point Screw Bevel CUT Work Clamp Stop PINTo Bevel CUT See Figures 30To Compound Miter CUT Compound Miter CUT Work ClampSupport Long Workpieces See Figures 3345 x 45 Compound Miter CUT Long Workpiece SupportsCutting Compound Miters COMPOUND-ANGLE Settings for Popular StructuresPitch Side Cutting Crown Molding Laying Molding Flat on the Miter TableCeiling Inside Corner FenceUsing a Crown Molding Support JIG Making a Crown Molding Support JIGCutting Warped Material See Figures 37Maintenance Clamping Wide WorkpiecesGeneral LubricationBrush Replacement Proceed as follows when replacement is requiredBrush Assembly Brush CAPChanging the Batteries Do not attempt to activate the laserPage Warranty DAY Satisfaction Guarantee PolicyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredCustomer Service Information Model No MS1250LZ Serial No