RIDGID AC99401 manual Mounting Other Brands, Center the Miter SAW on the WORK- Stand, Length Stop

Page 9

ASSEMBLY

MOUNTING OTHER BRANDS

See Figure 8.

NOTE: Other brands of miter saws (not RIDGID miter saws) will require additional 5/16 in. mounting holes to be drilled. See instructions below.

nLocate the following parts:

Hex Bolts, M6 x 40mm (4) Flat Washers, M6 (4) Fender Washers, M6 (4) Lock Nuts, M6 (4)

CENTER THE MITER SAW ON THE WORK- STAND

Check and make sure

n The front of the miter saw faces the front of the workstand as shown above.

nThe miter saw is mounted so the workpiece is positioned in line with the roller assemblies as shown above.

nThe mounting hardware will not interfere with the sliding table frame members underneath table. Shaded areas on table in figure 8 show locations that mounting hardware may interfere with folding/locking mechanisms. Be sure to position miter saw outside of these areas.

nMark the mounting hole(s) location. Remove miter saw.

DO NOT DRILL

HOLES IN

SHADED AREAS

Fig. 8

nDrill 5/16 in. mounting holes.

nReposition the miter saw on the workstand.

nSlide flat washer on hex bolt and place through miter saw and workstand. The larger fender type flat washer can be placed on the bottom or top of the miter saw. Certain mountings will require this washer to be placed on top of the miter saw in order to provide clearance with the frame. On some miter saws using mounting position “C”, it is necessary to mount the hex bolt and flat washer from the bottom side of the table on the rear of the miter saw to allow clearance with the frame when folding the stand in the upright storage position.

nSlide a flat washer on hex bolt and “finger tighten” using lock nut.

nRepeat above steps for the other three mounting holes.

nTighten all lock nuts.

MOUNTING AND ALIGNING ROLLER ASSEMBLY

See Figure 9.

nInsert roller assembly into each extension bar.

NOTE: Make sure length stop is positioned towards miter saw.

NOTE: Load capacity of each roller is 100 pounds maximum.

nPlace a straight edge on the miter saw table and adjust roller assembly to table height.

LENGTH

STOP

Fig. 9

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents OPERATOR’S Manual Introduction Table of ContentsRead ALL Instructions Rules for Safe OperationSafety and International Symbols SymbolsUnpacking Loose PartsTools Needed Attaching the Lower Foot AssemblyMounting Wheels See Figures 1 dSetting UP Workstand SET-UPSee Figures 4 Compound Miter SAW Mounting Miter SAWRidgid Mounting Holes See Figures 6Mounting Other Brands Mounting and Aligning Roller AssemblyCenter the Miter SAW on the WORK- Stand Do not Drill Holes Shaded AreasExtension Bars Operation Adjustable Handle Locking PIN KnobSee Figures 10 LEG Foot KnobFolding LEG and Table Folding and Moving WorkstandSee Figures 12, 13, LowerKeep Area Clean Lubricated MaintenanceTransporting Tool See Figures 161937 Exploded VIEW/REPAIR PartsPage DAY Satisfaction Guarantee Policy WarrantyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredCustomer Service Information

AC99401 specifications

The RIDGID AC99401 is a robust and versatile air compressor designed to meet the demands of both professionals and DIY enthusiasts. Manufactured by RIDGID, a brand renowned for its quality tools, the AC99401 combines advanced technologies with practical features, making it a reliable choice for various applications.

One of the standout features of the RIDGID AC99401 is its oil-free pump. This technology eliminates the need for regular maintenance and oil changes, allowing users to spend more time on their projects and less time caring for the equipment. The oil-free pump design also ensures that the air produced is clean, making it suitable for tasks that require contamination-free air, such as painting and inflating.

Equipped with a powerful motor, the AC99401 delivers impressive air pressure and flow rates. This high-performance compressor can generate a maximum pressure of 125 PSI, providing enough power for a range of pneumatic tools, including nailers, staplers, and air sprayers. The compressor’s ability to maintain consistent pressure levels makes it ideal for both small-scale home projects and more extensive professional jobs.

Portability is another significant advantage of the RIDGID AC99401. The design includes a lightweight, compact form factor complemented by a sturdy handle and rubberized feet for stability. This makes it easy to transport to different job sites or around the home, while its space-saving design allows for easy storage in tight areas.

The AC99401 also features an integrated control panel with a quick-release drain valve, making it user-friendly. The gauges provide a clear view of pressure levels, ensuring that users can monitor their operation effectively. Additionally, the unit is equipped with a thermal overload protection system that safeguards the compressor from overheating, prolonging its lifespan.

Overall, the RIDGID AC99401 air compressor encapsulates a perfect blend of power, efficiency, and convenience. Its innovative technologies make it suitable for a wide range of applications, from simple household tasks to demanding professional jobs. With its durability and reliability, the AC99401 stands out as an excellent investment for anyone looking to enhance their toolkit with a dependable air compressor.
Top Page Image Contents